Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
I am currently testing DFU updates with nRF52. I have run into a situation where the upload of new image is interrupted for some reason. When I try to run the update again...
Target : NRF52832, SD S132 6.1.1. program on Eclipse.
Hello,
Intro :
I migrated to SDK 15.3 for my application and it works.
Then I migrated DFU to SDK15.3 too but...
Hello! I am developing a pcb based on nrf51822. I am trying to copy the layout of the PCA10028 at first. But I will not use the coaxial connector for an external antenna....
Hello!
I have next problem. When switching from backup power to main power, the controller loses data in RAM. If the backup voltage is below about 2.4V, then it is possible...
Hello,
I am trying to add bonding functionality with a passkey to HID device, and use for this ble_app_gls_pca10040_s132 example as basic project.
But it don`t want to...
normally the secCount in Eddystone TLM should be the t ime since power-on or reboot:
https://github.com/google/eddystone/blob/master/eddystone-tlm/tlm-plain.md
but the...
set the tx power of a tlm frame with the eddystone configuration service will result currently in an app error. call path is es_gatts_write_handle_unlocked_write -> es_slot_radio_tx_pwr_set...
The function documentation for pm_conn_handle_get says BLE_ERROR_INVALID_CONN_HANDLE is set to the connection handle pointer if the peer is not connected, however it is BLE_CONN_HANDLE_INVALID...
Hi,
I programmed nrf52840 dongle with simple ble_blinky example. The dongle successfully bond with my phone but when I tried to discover services and read characteristics...
Hi
I am working on nRF52832 DK and using Ubuntu 16.04 and Segger Embedded Studio as IDE. When I try to build the AES_CTR program, the following error comes up.
Can anyone...
Hi I have run a few peripheral examples ok and now move to evaluation of ble_peripheral also.
I'm using this version of the SDK....
If I program the softdevice and...
Hi
I am using Segger Embedded Studion on Linux 16.04 operating system. I have programmed softdevice, i.e, I have provided SRAM and FLASH START VALUES and other things. How...
Here is a list of problems I found. Please fix them.
nRF SDK 15.3
Examples: logging does not work in examples. I think the problem is related to this issue .
Documentation...
Hi there,
On my application, I have multiple sensors attached to the nRF52 and I read them every 5 seconds scheduling the read inside a timer handler, then when the Softdevice...
Hi Nordic Forum!
In the past, I set connection interval min to max is 20ms~75ms, it work ok for IOS。But on Android platform, Android use 75ms as actual connection interval...
