hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi,
Here I met a problem, please help.
I am using proxy.c to establish an data link with smartphone via mesh_GATT.
What I am doing is like this:
For TX ,
it is...
IDE: keil uvision 5.23, SoftDevice 3.0.0, SDK 12.1
Computer Platform: Windows 10
Receiving device: nrf52832_xxAA
In our project, there is a sender always advertising...
Hi,
I have a project where, I need to change the minimum and maximum (MIN_CONN_INTERVAL and MAX_CONN_INTERVAL) connection interval to higher values like 1 second and 2 second...
hi everyone!
I am developing NRF52840 with the Development Kit.
I am trying to use a GPIO to o capture a external HIGH-TO-LOW signal and then trigger a LED.
I I learned...
Hi all,
I'm currently using nRF Connect in combination with a nRF52 DK to connect to my Mesh network. So right now I have to type all my commands as HEX messages and decode...
Hello,
I'm trying to compile the Light_switch_provisioner example (Debug, Mesh 2.2.0) in Segger Embedded studio.
<t: 0>, main.c, 561, ----- BLE Mesh Light Switch Provisioner...
hello
i wanted to send message using the simple message model with some modifications from client to server periodically but didn't know from where i should start , i tried...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
hello dear, is there any pre defined function or library in segger embedded studio for I2C interface..? i want to make communication with digital temperature sensor(MCP9808...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hello.
I need to solve this problem urgently.
I have now created my own protocol and are testing.
At the point of this project is the guarantee of data transmission...
Hello All,
I am developing an application using Nordic nRF_SDK_15.0.0, in which I need to make my BLE peripheral device as a peer device which will get/set data from/to...
Hello,
I am developing application for nRF52832 based SoC using nRF_SDK_15.0.0. I need to develop number of custom characteristic using given sdk. For reference, I am using...
Hello.
I'm trying to understand how to programm my nRF52 DK (PCA10040 - Rev 1.2.1) with SEGGER Embedded Studio (in Windows 10 - x64), however I can't follow all the tutorials...
