Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi Sir,
we use 52832 ESB , one PTX and two PRX. (PRX_A and PRX_B)
A and B have same base_addr_0 and base_addr_1 .
diffrent addr_prefix
PTX send package to A and wait...
I am trouble with adding DFU function to BLE_UART on nRF52832. I have just followed those step in this link Adding DFU to your App . But when i compile and fash to my device...
Hi all, My company is doing a proyect with BLE. We use nRF51822 with the softdevice s130. I am preparing the FCC and CE certification. Our tester asked us to prepare 2 samples...
hi, nordic team:
Now I am using the nRF5 AirFuel SDK version 2.2.0 to develop the PTU and successfully use the serial to do the dfu function.
I used nrfutil for DFU, but...
Hello, I trying to debug with GDB server Because of this .
I open the GDB server like this
go to build directory and write client cmds below
output is $4 = {<error...
SDK12.30 supports S132 V3.0. Is there any other version SDK supporting S132 v3.1?
Any problem for firmware built with S132 V3.0 and running on module with S132 v3.1?
Hello,
I've disabled the buttons in light_switch example for the client DK. I'm using GPIOs for input and I want to enable BSP_BUTTON_3 to reset mesh network configurations...
After switching to SDK 15 from SDK 14, stopped working correctly transmission of HID Report Descriptor over USB, what in case leads to incorrect device enumeration.
Now...
I'm developing a database with FDS that stores application-level data that must be able to be matched to bond data. After looking at the files for Peer Manager, ID Manager...
Hi All,
What is the recommended way to choose FIFO and buffer sizes for the nrf_serial module? I mean the optimal values for the following constants:
SERIAL_FIFO_TX_SIZE...
Hi,
the pull-up resistance Rpu of GPIO pins as stated in Product Specification v3.1 in Table 62 is supposed to be 13 kOhm (typ). Since we measured a different value on pin...
I started development with the S132 (SDK 15.0.0) peripheral example "blinky". After some modification, it handles all necessary communication with my phone flawlessly. Now...
I'm attempting to use the USB MSC example (from nRF5 SDK v15.0.0) with external flash chip replaced with Winbond W25Q128FV and I see the following logs:
[00:00:00.000,000...
Hi,
I have designed a customized for nrf52832 with a trace antenna. I haven't used any low pass filter and made the changes inside sdkconfig.h file to use RC and that board...
Hi,
I'm using nrf51822 module purchased from www.waveshare.com/core51822.htm . I'm running uart over ble application example. I commented uart_init() function in main(...
