I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello!
I'm trying to read data off of a commercial blood pressure monitor (Qardio arm) using an nrf51822 with the nrf51 SDK v10.0.0 as the central role (s120). I am able...
I am unable to build any example project of nrf sdk for mesh. I have added the SDK root in my global macros as : SDK_ROOT=C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a . And still...
I run the below code on nRF52DK and measure the power consumption of the chip (using nRF current measurement jumpers). The current consumption is 0.47 mA which is a lot just...
Hi,
I am using nRF52832 board. I want to connect serial mesh example with 'ble_app_uart' . I try to use the same method http://infocenter.nordicsemi.com/index.jsp?topic...
Hello,
I have 8 12-bit ADCs that produce 3300 samples per second, which I will send over a Bluetooth link, so I need a data rate of about 320 kbits/s. I was thinking of...
I get to the point of having the EP0SETUP event being generated, I check BMREQUEST and WVALUEH and see that it's a request for the device descriptor,this is on windows and...
Hi, I am using:
SDK v15 with nRF52840 chip running in soft device s140. I am Using Segger Embedded studio.
I want to update a application( Say Blinky) thorugh DFU. I perform...
Hi, I'm using Atomic_FIFO library and for my application I need to know the number of elements currently in the fifo, the library itself doesn't provide any functionality...
Hi,
The program will crash when spi transfer on NRF52810. The crash occurs in spim_xfer function, immediately after spim_int_enable function calling,
but if i remove the...
Hi,
nrf5_SDK_for_Mesh_v2.0.0_src
When complete provision a provisionee , provisioner will assign provisionee a mesh key and device key.
Now i want to know how to calculate...
I can get a clean build and working product with some workarounds, but a couple issues remain from migrating sdk 13.1 to sdk 15.0 (SES nrf52832 s132).
1) After nrf_drv to...
Hi,everyone.
I had learn for below Links and compiling is no error.
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104063#104063...
Hi,
I'm having problems to run the Loopback example in the Bluetooth Mesh SDK:
infocenter.nordicsemi.com/index.jsp
I'm receiving a timeout.
My setup is as follows...
This is a duplicate of https://devzone.nordicsemi.com/f/nordic-q-a/35127/spi-master-0-uses-300ua-upon-first-transfer but I wanted to be safe because I pre-maturely verified...
Hi,
I have been working on MPU9250 examples given in here .Though the program runs fine in KeilUvision 5, the output in tera term shows only 0,0,0 for Accelerometer values...
