Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
My config :
Board NRF52DK
SDK 14.2
Segger ES Release 3.30
SEGGER J-Link V6.22a
macOS 10.13.1
I want to use RTT to debug my code. As a starting point I've...
The manual clearly states that the external HFXO should be 32MHz. However, if one would like to have precise 16kHz on the PDM and I2S interfaces a 32.768MHz crystal is required...
I know that RF52840 could act simultaneously as the Advertiser\Peripheral and Observer\Central and I saw Nordic's recent demo video of BT + Thread co-existence. However, it...
I am having very limited knowledge in flashing devices, infact this is the first time I was doing it, pls conider
Step 1: I bough PCA10040 and installed nRFGo software in...
I have found multiple PDFs indicating the lay-out on the nRF52-DK. However, none of them tell me anything about the size of the kit. Does anyone have a PCB lay-out with at...
Using the latest SDK and following example multiprotocol/ble_app_gzl.
I try to add a vendor specific UUID and get error 4. Which means, not enough room in some table? Whose...
Hi,
I hope this is the appropriate forum for this question. I've also asked this on the developer forum on thisisant.com, but received no answer there.
We are using...
Hi all,
I have a custom board with 3 LED's and one button. I have created a custom_board.h file:
#define LEDS_NUMBER 3
#define LED_START 22
#define LED_1 22
#define...
I wanna build project nRF51822 using ADXL345 for accelerometer sensor that program using eclipse or keil. can you teach me how to build using nRF51822 SDK version 6 or higher...
Hi,
I'd just start developping with the nRF52832 and I would like to communicate with a sensor using the I2C protocol. Has I am a stranger with the nordic uC, I would like...
Hi guys, me again.
I was very confused with my current process on developing with nrf chip now... so I would like to post my develop step and some problems I had so maybe...
I am using ATT MTU throughput example and I noticed that using CLI (calling cli_start) causes the main while(1) loop forever. In other words, wait_for_event does not block...
I just received the Nordic nRF52-DK, and am unable to do anything with it as my laptop does not recognize when it is connected. I do not have the original cable as I did not...
Hi!
I have AD5611 DAC connected to nRF51822 by SPI.
In DAC datasheet we need to send data by MSB first order.
Data packet is 16 bit length.
I feel variable uint16_t...
