Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Hello!
I use the NRF51228 board like this PICTURE
The ICs revision QFAAH0.
I use Keil-uVision 5.17 and ST-Link V2 from STM32F4 Discovery board to load firmware HEX as...
Hello,
I am just getting started with my nRF52832 and went through the first getting started tutorial . I use the SDK V11 with Keil and Termite as described and an iPad...
Hello,
I run ble_peripheral\ble_app_uart example from this link : devzone.nordicsemi.com/.../36
Used PCA10040, SDK 11, S132 2.0.0
I use Termite3.2 and IOS nRF toolbox...
Hello, I am toggling two separate pins at different rates but it looks like for whatever reason the when I go to clear one gpio register it clears everything. I understand...
Hello,
I would like to make use of white list advertisment for my heart rate application on my nrf52832 s132 pca10040, currently I am using SDK12.2, is there some example...
Hello,
I used translation software.
I'm looking into LDO mode and DC-DC mode.
However, I did not know what LDO mode and DC-DC mode are.
What are LDO mode and DC...
I'm working on a project that will utilize the nRF52832 as the Host and Controller and an STM32F3 as the application using serialization.
I've included the nRF5 SDK V14...
We just produced a PCB with a NRF51822-QFAB-R7, does Nordic provide a EMC test firmware that we can flash onto the chip? Basically need it be always transmitting....
Thanks...
I'm using the original BLE App UART from nRF5_SDK_14.0.0 on a PCA10056 Board.
The board is advertising, but if I want to open a BLE peer-to-peer connection, than the application...
With SDK 14.0.0 and Softdevice 5.0.0 I have problem with Windows 10 connection. The device connects to PC but then almost immediately disconnects with reason 0x13 (BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION...
Hello,
We developed a few devices using the nRF51822 and noticed that the receiving range is reduced significantly from our nRF24L01 devices. The transmission range is good...
Hello,
I'm trying to measure the current profile with the PPK (HW Rev:1.1.0, SW: 1.1.0) but I see a lot of strange behaviors.
My firmware initializes everything and the...
I am running a nrf52840 dev board as an NCP connected to a RASPBERRY Pi running wpantund.
I have 10 other nrf52840 devices in the network. The PI has LIBCOAP coap-client...
