Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Classic C documentation issue. Are the values that are passed by pointer (p_peer_address and p_whitelist) to sd_ble_gap_adv_start() copied into that function, or do they need...
I'm trying to read the 32-bit value of TIMER1, but it seems the value I read is always 16-bit value. When I debug the value is never above 0xFFFF.
snippet from nrf_drv_config...
The peripheral is actually a dual-mode device, with BLE being a peripheral device.
I can connect to this device and discover the GATT services with the nRF Connect iPhone...
What is the minimum and max value that the NRF_RADIO->TXPOWER register can get set to? The datasheet it takes a signed 8 bit for the setting, but what happens if you set it...
Hello,
I am trying to read data from nRF51422 ADC using SDK51 PCA10028 board downloaded with S130. I tried one of existing ADC with Softdevice examples, it seems to work...
I have meander antenna design on my board with matching network(similar to PCA10031).
Since I don't have access to VNA or Spectrum Analyzer for tuning antenna, I am tuning...
I'm building some code off of the twi_master_using_app_twi example which is available in the SDK (v11.0.0).
The two peripherals I'm working on are an accelerometer (LIS3DH...
I've just upgraded to Windows 10, and I've found that the PC freezes completely (i.e. no mouse movement, no keyboard response) when I unplug an nRF52 DK board. When I plug...
Hi,
In my application, I need 3 PWM to drive LED. Each PWM will have the same frequency but not the same duty cycle.
Is that possible to do that?
I know that Timer0 is...
hi
on android side of my project i try to disconnect from gatt by this code
mbluetoothGatt.disconnect();
but in nrf51422 this event not trigering
static void on_ble_evt...
Hello, I am working on low power modes and I got trouble finding the code to switch from NRF_POWER_MODE_CONSTLAT and NRF_POWER_MODE_LOWPWR. Can anyone please guide me to better...
Bonding causes power consumption to rise.
I have a central and peripheral device communicating using the nus-service. The peripheral device is running FreeRTOS with tickless...
Hi,
I'm trying to test the DFU over HCI included in the SDK examples but I can't make it work. This is all the information of the environment I'm using:
SDK: 10.0...
Condition: nRF52, SDK11,s132, SDS v2.0.
Using the sd_ble_gatts_hvx() in timer1 interrupt service(timer1 interrupt priority is set to level 3) will result in hardfault. While...
I am using SDK_11 s130. I am looking at app_error_fault_handler() in app_error_weak.c
Inside app_error_fault_handler(), there is this line of code;
UNUSED_VARIABLE(bsp_indication_set...
