Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Hi,
I want to advertise multiple UUIDs, one after another
Do I have to stop advertising, or is there a way, that I can update the struct in the background?
Currently...
I have two UART devices on a custom board with an nRF51822. I've just upgraded the SDK I use from 8.1.0 to 10.0.0 and one of the UART connections has stopped working, but...
Totally get the limitation of 3 PWM channels.
Wondering if I can dynamically re-assign which 3 pins are tied to the PWM outputs.
At boot time, I call this function:...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi All,
I have got reliable writes working on nordic side (nrf51822 eval board).
Tested them with master emulator dongle by using write long button on MCP on PC.
I...
Hi, I'm porting my project from SDK8.1 to SDK10 and got a problem in app_timer.c
Main chip :nRF51822 QFACA1
Crystal:32Mhz, no 32.768
Initial is fine.
APP_TIMER_INIT...
Hi, I realize that the compatability matrix states that SDKs 7 8 and 9 are built for rev3 of the nrf51822 and nrf51422. It has been mentioned however that they may still work...
The S130 SD supports up to 3 concurrent central connections. Once it has made the maximum number of connections can it still scan for non-connecting peripherals, e.g. to look...
I have 2 PWMs working with the version 8 softdevice on an nRF51422, and it's straightforward enough to change the duty cycle with app_pwm_channel_duty_set() in the app_pwm...
The way of entering the bootloader mode is sending the command,then run the code as follows:
void jump_to_bootloader(void)
{
uint8_t softdevice_enabled;
uint32_t err_code;...
I'm sorry but i don't know where else to turn. The tutorial on adding a characteristic to a service (the nordic tutorial i am basing this off) isn't finished and I have no...
Hi
I did not quit yet understand the Gazell Pairing library.
If an encrypted message is send, how do I add some payload to the acknowledgement.
And how will I be able...
Hi,when i set NRF_RADIO->MODE in RADIO_MODE_MODE_Nrf_1Mbit ,then use radio_tx_carrier(txpower_, mode_, CH_LOW); i got a picture with spectrum analyzer like this ! , when i...
