hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi,
I want to design one BLE braodcaster and one BLE observer using nRF51822 chip.
What should be the advertising interval time and receiving interval time (with receiving...
Hi:
I am using the ANCS from SDK9.0 ,SoftDevice8.0 and iOS8.1.3.
Every time when I run ANCS, SPI will often crash.and error codes is:NRF_ERROR_BUSY.
Don't know if...
Is there any extra requirements When a Android APP connect to my Ble Decice? I want connect to my Ble device(51822) by my Android APP(EZ-GUI Ground Station V3.208.208), But...
We have the bootloader working over serial at UART_BAUDRATE_BAUDRATE_Baud38400. We took a big leap and tried it at UART_BAUDRATE_BAUDRATE_Baud230400 and it failed. We will...
Dfu not working when i try to upload my custom made application second time.
nrf51422 sdk v8.0 and softdevice s110 on pca10028
the steps i used to do dfu are as
1)programed...
Dear all
I have some questions about nRF51822 bluetooth smart beacon kit, I read the User guide, but I can't get information about the following questions:
1、what is the...
I want to change bootloader start address BOOTLOADER_REGION_START to 0x33800 to store user data and DFU. But when I only change BOOTLOADER_REGION_START, my device can't work...
Dear Developerzone Board
Does the nRF51822 Sniffer just start with the conversion over all advertising channels or do I need to send a start command? Which command set...
The ENable pin on addition hardware component requires "floating" to power on, and drive low ( less than 1.25V) to turn off.
Unclear based on my understanding of the chipset...
Hello
Is there a way to stream data from one nRF51 device, to a second nRF51 and have the received data sent over UART to a host PC? Basically in my setup, I have a custom...
I'd like to understand why BLE_GAP_ADV_TYPE_ADV_IND is used while using a whitelist.
An example application that does this is the ble_app_proximity app. You'll see the...
Hi.
I need to use multiple SPI devices and I'm not sure which is the proper way to handle this, should I open/close each time the SPI port with different SS pin configurations...
Hi,
I wonder if nrf51822 has a clock inside it.
It doesn't need to be real clock
but It's important to me.
I store datas on flash and send it to the phone when it...
