hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi everyone, I am attempting to configure two of NRF5340DK modules to execute ISO_Connected_Benchmark. I have tried to configure ipc_radio to compile for cpunet and application...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hello,
I would have a question regarding the use of PCAL6408A I/O expander on nRF9151 DK. The buttons and LEDs on nRF9151 DK are connected both directly to the processor...
We are planning to run a small proto build, and looking to program a small quantity of nRF54L10, prior to the SMT. These are loose parts (not built onto any PCBA). I am hoping...
I recently switched from evaluating an nRF52805 (Fanstel BC805M) to an nRF54L15 (using the nRF54L15-DK), and after I updated the toolchain and tried to flash the kit (using...
checking in if anyone is successfully using an open debug-probe for nRF54L series?
...guessing nordic is using segger OB on the DK's because of the Risc-V not fitting...
Hi,
I'm evaluating the nrf5340-DK board. I have a question about LED5 state. I tried following power sources:
usb J2, sw9 in VDD position - LED5 lights and I can detect...
Hi,
In the example ras_initiator for channel sounding, there is a macro set for maximum TxPower:
where #define BT_HCI_OP_LE_CS_MAX_MAX_TX_POWER 20
In the...
After looking over numerous other devzone tickets and google hits... I cannot get host name to IP address resolution to function on the nRF9151DK. The original source code...
Hello,
I am working with a board (currently embedded inside a clear container I cannot easily take it out of) with an nRF52832-CIAA-R. We were taking photos of it with a...
Dear support team and community
After some days where it worked perfectly, our nRF52840 suddently stopped connecting anymore to a Motorola G4 plus running Android 7.1.1...
Hi, We have tested beacon sample in our custom board. Build with nrf7002dk_nrf5340_cpuapp_ns board config. Facing below issue but the same build is working fine in nrf7002...
Hi all,
I have an issue regarding multiple GPIO interrupts. Following case:
I am using MCP251xfd can module connected via SPI and an interrupt GPIP int-gpios = <&gpio0...
