I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
Hi,
Just to be clear, you are looking for reference DFU controller firmware for the Host MCU, in order to upgrade the firmware on the nRF52832。
I also need this feature...
Hello Developers,
I have configured a mesh network where I have a gateway node and multiple relays to relay messages from End nodes (sensors)
My question is the following...
Hi. I am working with nrf52832 trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
hi.......
i need to run the program continuously using timer ......and want to check the data every one minute how to do that
i have seen timer example .. i am confused...
I am using nRF 5 SDK v 14.2.0.
I'd like to change the tone of the buzzer, how can I do it?
I'd like to make the following three settings.
Treble (+ 1 kHz), normal (+0...
HW: nrf52840
SW: nRF5_SDK_15.2.0_9412b96
source code: blinky_rtc_freertos example
Q1:
I read freeRTOS xtaskcreate operation on the web, it seem that I just need to...
Hi,
I am using Segger IDE.
I encounter error undefined reference to `nrf_drv_rng_init' .
I have include the below header file;
#include "nrf_drv_rng.h"
I already...
Happened when I occasionally compare the NRF_TWIM_Type struct in nrf52.h with the TWI registers (table 127) in nRF52832 Product Specification v1.4, there are many differences...
Will there be an HTML version of the nrf52832 spec document?
I hope Nordic is not expecting me to manually browse through a 550 page pdf document. I regularly use the infocenter...
I'm having trouble implementing the workaround that was mentioned in the following previous post: https://devzone.nordicsemi.com/question/55937/nrf52-sending-an-octet/
...
Hey guys,
i am trying to add new firmware to a cheap fitness tracker I have. After I write the new firmware in the Nordic SDK, I think I save it as a hex file. I’m not sure...
Hey Guys, I am trying to calculate goodput and delivery rate using nrf52840 pdk devices in ble mesh. Does anyone had already tried it before and shed some lights on starting...
Hi!
I am planning to port SPI sending and receiving functions to the sample code of ble_app_uart of SDK 14.0.0.
The transplant was finish, but when I am debugging, if...
https://www.nordicsemi.com/eng/Products/Getting-started-with-the-nRF52840-Development-Kit
Hellosupport,
Just got my 52840-DK board (v. 1.0.0), got the pulsing LEDs...