I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
Hi ,
I am using nRF51 SDK with S130 soft device lib, and it is running well when downloading the example of ble_app_uart. But when I want to modify the service UUID from...
Hi,
I'd like to check the battery level in my BLE device, and I can set a timer to handle the checking, however this means that Timer 1 would need to powered up, and hence...
Hi,
The situation: nRF51 has established a connection with the iOS/Android (custom made)App. The nRF51 goes out of the Bluetooth range. Eventually, the Bluetooth connection...
I have looked around but have been unable to find doc explaining this. If there's something around, I'd truly appreciate a pointer.
I have an existing (solar powered) device...
Hello,
i'm searching for informations about calibrating the SAADC of the nRF52. And i have read here: Link
For nRF52, there are no calibration
values that I know of...
Hi Sir/Madam
I wrote a small program for low current verification on nrf51822 development kit with starter mother board.
The program is based on "blinky_example" project...
Hello to all,I have developed a board using the NRF51822;
Currently I am using SDK v11, S130 v2.
I have a problem in my bootloader, since bootloader_app_is_valid (from...
Hi, i want to jump from my app to the bootloader, i used the function
void bootloader_app_start(void)
{
vMBt_eStopAdv_Exe() ;// Stoping the BLE ADV
sd_power_gpregret_clr...
I have a question about when the application is erased during serial DFU single-bank update:
According to the S110 Serial HCI documentation , the serial update packets...
Hi,
I just purchased an nRF51 sniffer. I have set everything up as per the UM. When I invoke the sniffer application, it says scanning for devices, but nothing shows up....
Hello.
I'm investigating how bootloader works (bare minimum), especially how it brings control to an application (already flashed at 0x1B000, s130 SoftDevice also present...
Hi,
I'm creating a simple SPI bootloader without SD for nRF51822 based on this post
The bootloader is connected to Freescale 22F through SPI and it will be without any...
Trying to build the examples for the NRF52 and ant. I have the latest download of SDK11 (nRF5_SDK_11.0.0_89a8197)
It looks like paths are broken as well as missing the ant_interface...
Hi,
I want to communicate with other chip on UART.
the chip on other end requires AT(CR,LF) command to start communication over UART.
UART is setup correctly, but it...
