Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I am working with signled door sesnor and it supports ZigBee 3.0 as it has an install code and mac address on the side of the sensor in the form of a QR code. When I run the...
We are using the latest pc-ble-driver with SoftDevice v6.1.1 and latest connectivity firmware on an nrf52832 (s132) which is connected via usb-uart.
We were previously using...
Hello!
I am flashing software over USB as I do not have a 10-pin JTAG cable yet. After I flashed a sample file on to the Thingy91s SIP it is no longer showing up in nRF...
When using LE Audio with multiple sink devices, can those sink devices also communicate between them via master Bluetooth source? For example: During streaming audio, 2 or...
My goal is 11.25 ms for connection interval with iOS. With PC and Android i can setup it.
Following Apple guideline, I added HID service to my custom device(it works, i...
Hello everyone,
I'm a junior engineer in a company, and I'm assigned to that project which we will use a different microprocessor with BLE in it, and it needs different...
I am currently working on a project with a nRF9160 and in the very early stages of evaluation.
I have a few, hope not too many questions that I hope can be answered here...
I have been struggling to get the DFU in our own application to work. When starting a DFU from the desktop nRF Connect 3.4.1 it reports an error:
According to the log...
Hi,
We are using nrf52840 development board and segger embedded studio. I am using thread concept here to run another function in parallel to my main function. i want to...
Device: nRF52840, nRF5 SDK16.0, Softdevice: S340 (ANT_s340_nrf52840_6.1.1)
Hello,
As next step to increase usability of our product and adding new features, we have...
I hope someone is able to answer a few question.
I read quite a lot but still some things are still confusing.
If we use e.g. the AMB2621 Module of Würth, is skipping...
Hi,
I am trying learn about IO/ events that can wake-up nRF52833 from lowest power mode.
What qualifies as event that can serve as wake-up source?
Is it possible to...
Dear sir,
Got error while uploading .zip in DfuTarg as "SD version failure". I'm using nRF52840 DK board. I have tried to create .zip by --sd -req 0xB6/0XAE/0xA9. zip get...
