Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
Is a TVS diode clamping voltage of 6.5 V acceptable for supplementing the built-in ESD protection of the NRF52840 GPIO pins?
It has been previously established in the forum...
Hello everyone!
I am rather new to firmware development with Nordic products and am experiencing some trouble with the Thingy91 LTE BLE Gateway sample.
What is the problem...
Hello,
I want to set my TTL value in a node (nrf52840 dongle) that i use as a relay node.
In prj.conf file I set the node in this way:
CONFIG_BT_MESH_RELAY=y
CONFIG_BT_MESH_RELAY_RETRANSMIT_COUNT...
Hi
I've recently tried to move from SDK version 2.6.3 to 2.9.1. However i've run into issues with this transistion.
I made a new custom board, by following the guide...
Hi , i am trying to use ble channel sounding feature through hci uart with an external host. I am sending CS commands but getting the following error for one of the commands...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
I want to realize the connection and communication between the broadcaster and the upper computer software nRF Connect...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hi Nordic team.
I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
I have a few questions about the new privacy requirements added to the RED for CE certification starting in August 2025:
Does ANT+ still comply with these new requirements...
Hi, AFAIK, factory data is written during production and will not be modified later.
Will the factory data be modified after FOTA?
I noticed that the certificate declaration...
We are developing a new board based on the NRF9151 and would appreciate some guidance regarding the power supply design for the modem.
Specifically, we’re looking for documentation...
Hi,
I still have problems understanding the port and pin assignment for peripherals on the nrf54L15.
I need up to three SPIM, one UART and one TWI. That should work, right...
For VDD-nRF in the nRF54L15-DK schematic When I check the schematic, I can't tell which part is internally generated.
When I check the actual board, VDDM_nRF and VDD_nRF...
Hello,
I'm currently testing BLE Coded PHY by using extended advertising.
I used two nRF52840-DK and nRF5 SDK v17 with compatible softDevice.
I've checked that the...
Hi,
I am running Matter TH.
Among them, there is an error in the TC-DA-1.2 test step 6.9 certification_type check.
The reason for the error is that the certification_type...
