hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
nrf_ringbuf has many logic bugs that cause it to both corrupt internal structures and return invalid data. For example one of these calls to nrf_ringbuf_alloc tells me that...
How to calculate the Distance between the central and peripheral where the peripheral is transmitting power at -40 dBm and my rssi value is -100 dBm ?
I'm using the nRF52...
Hi,
I'm wondering if the nRF52810 supports Central mode. I noticed that currently only the S112 is intended for production on the nRF52810, which only supports Peripheral...
Hi,
I came up with one application where i will be using one master and multilateral . with one master i want to scan all the the available peripherals and display it on...
Hello,
I´m using nrf52832 with sdk 14.2.0 and softdevice s132.
I'm trying the example bootloader_secure_ble and compiles me correctly.
The problem is that when I debug...
In a documentation i read that i can transmit power at minimum of -40 dBm ?But i cannot achieve my target as my range has to be minimum of one meter?
So how do reduce the...
After getting SDK 12.1 and the S332 v2.0.1 softdevice working, I started working on updating the bootloader from the S132 bootloader we've been using to supporting the S332...
I am trying to set up a humidity sensor over I2C and I'm trying to use the twi interface. There are examples where the app_twi interface is used. I am however unable to get...
I'm working with a development prototype board with the nRF52832. It is connected to a main processor in our design over UART. We are working towards being able to do the...
Hello Nordic team
I am working on nRF52840, SDKv-15.0.
Is there any example code available which can send message from central device to peripheral device apart from ble_app_usrt_c...
Hi,
I'm tring to enter DFU mode by combo keys by KEY_COMBO_TWO_KEY_REGISTER().
In v1.1, I used m_pwr_mgmt_shutdown(M_PWR_MGMT_SHUTDOWN_TYPE_DFU) to enter DFU mode directly...
I'm looking at decreasing the motion sensor update rates for the Thingy:52 to get less frequent readings into the sample app. I have seen in the MPU9250 specs that I don't...
Hello Nordic team
I am working on ble_uart_c central example on nRF52840 DK, SDK v-15.0.0. Example code working correctly I can exchange data between peripheral and central...
Hi I am trying to reduce the power consumption of the badge of my company as much as I can. We use a proprietary radio protocol on the nrf52832.
I'm currently developing...
