hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
hello! i want to send mac address of my bluetooth device. i have written function
uint32_t get_address(void)
{
uint32_t err_code;
ble_gap_addr_t ble_gap_addr;
memset...
When I open the project dfu_dual_bank_ble_s110_pca10028 and configure it for nRF51822, it compiles fine, but flashing does not succeed. I get errors:
No Algorithm found...
I loaded the "dfutarg" dfu program "dual bank version" to the development kit & then used this dfu program to perform firmware over the air, the firmware I need to upload...
I've been trying to get my head around the TWI on the nRF51822 today, using the "twi_sensor_pca10028" example to begin with.
Firstly, I still don't quite understand how...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi All.
For my project I need a very long range BLE Communication. Don't know if its possible to get a range close to 1 Mile LoS. But my goal is to meet max possible range...
main.c Hello everyone
i am trying to configure two GPIO pins for PWM in order to increase the sound level of the buzzer i am able make the buzzer beep sound by referring...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Some nRF51 modules are sold with metal covers preventing visual access to the chip and date code. Is it possible to identify the revision of a nRF51822 through the Cortex...
I have my development board nrf52 PcA10036 and I am trying to run a ble basic example. I started using the blinking program and it works without problem, therefore i got full...
Is it possible to manufacture a RFID tag that works within the 2.4GHz wifi wavelength range allowing a mobile-phone to power and pick up data from this RFID tag. Data would...
I have a application which can enable and disable the softdevice.
I need the softdevice only to send some informations, after the sending the stack will be disabled.
...
I have a Nordic micro-controller nRF51 with 128kb of flash memory, I compiled with Keil, I generated a a program with:
Program Size: Code=23856 RO-data=632 RW-data=308...
I want to enable Notifications in my Central for a particular characteristic advertised by my Peripheral. There's example code that is supposed to do this in the BLE Central...
