According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
We've derived a DTLS handshake test firmware from github.com/.../l5_e2_sol
Tests have been done using nRF9151 DK, SDK 3.1.0 and modem firmware 2.0.2.
First we verified...
I'm putting together a project that requires a "large" (1500mAh+) rechargable battery, both because of the desire for long times between charges and to enable powering a peripheral...
Hello Nordic Support Team,
I'm working with the Android-nRF-Wi-Fi-Provisioner library ( https://github.com/NordicSemiconductor/Android-nRF-Wi-Fi-Provisioner ) and would...
I'm using the Nordic nRF52840-DK. I'm having a hard time with logging using RTT. Sometimes it works, sometimes it does not. Usually I get a few runs where it works, then it...
I developed a custom application on the 52840DK and have now moved this over to a custom PCB of my own design. I can compile OK and can start a debug session from "main" but...
I am unable to download the nrfjprog command line tools from your website.
I am using SDKV1.8.0 and Toolchchain V2.0.0. in Visual Studio Code.
When I attempt to flash...
Hi,
I have low power environmental sensor. They raise an interrupt that something was sensed and require to read some registers on the sensor via I2C and run a state machine...
Currently, the nRF Connect extensions are available only on the Visual Studio Code Marketplace. We primarily use Cursor, which is a VS Code fork designed for enhanced AI-assisted...
Hello everyone,
I’m currently working on implementing the PK peripheral using Rust with the SVD files for the nRF54L15, but I’m running into a documentation issue.
In...
have a MONOGOTO SIM card that works successfully with TELIT and THALES modems. However, the same SIM card is not detected on the NRF9151-DK. When I send AT+CPIN? , I get:...
Hi I’m having trouble connecting to my nRF5340 dk using nRF Connect for Desktop (Programmer app). When I select the device, I get repeated errors like:
Details:
...
Hello, I’ve been trying to install Nordic Connect SDK 3.1.0 in VS Code, but the installation keeps getting stuck midway and never completes.
I’ve tried several times over...
I'm bringing up a custom board, working through the peripherals one at a time. Unfortunately, I haven't gotten very far before things started misbehaving. One part of the...
With mfw 2.0.2, AT%RAI supports now also "2 – Activate with unsolicited notifications."
That's verfy useful, but I miss some details in the documentation about the usage...
Hello community,
I am working on a project that requires the integration of the u-blox NINA-B302 module , which is based on the nRF52840 SoC .
I have previous experience...
