Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I'm using SDK12 and SDK15 on nRF52832 and nRF52840 (peripheral and central), although this would appear to be an issue with other devices too.
If I connect with NRF Connect...
Potentially related to : nRF Connect v3.9.3 does not detect external j Link programmer - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com) , but I don't see the...
Hi,there:
I was used 2 52832 board to run the linght switch server/client examples to test message communication. I add the mesh events handle like this:
Then run the...
Hi,
I am trying to transfer a dataset of over 100k, via a custom service from a peripheral device.
There are many posts in this forum that describe ways to do this but...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. The Client sends unacknowledged messages to the Server ( APP_UNACK_MSG_REPEAT_COUNT...
Hi,
We are facing some issues with the DLE update.
The given table shows that the softdevice set data length and time.
Event Length (ms)
ATT MTU (bytes)
Data...
I'm trying to build "application_update" sample. I created a new application from sample. added build configuration for nrf9160dk_nrf9160_ns board and changed to variables...
Hello,
I have the Feeling with nrf connect programmer you can't select the Network core.
I use Programmer Version 2.2.0 and have our own hardware but also the nrf5340...
Hi Dev team,
I have been working with code development using Thingy91 and NRF Connect for Desktop. I use GitLab to maintain and manage my codebase.
I wanted to use GitLab...
I have nrf52840 pcb without xTAL.
In this ticket ticket I have discused about start Zephyr project without XTAL onboard.
But now I faced with other issue to start mcuboot...
Hi everyone,
I'm using nrf52840 as a connectable advertiser. Used ble_app_blinky example with some modifications. And I reduced the advertising interval to 2 seconds....
Hi, I'm using the example "libuartes" and developing 2 UARTE. But I dont know how to recoginize what port are communicating with external device because I only have 1 uart_event_handle...
Hi, Im trying to use nrfjprog from inside a docker container (ubuntu). I have started the container with --privileged and it seem to work but when i try to run the container...
Hello.
I use nRF52832 with SoftDevice and several TWI-connected IC's.
The power consumtion of nRF52832 is 14 uA after TWI initialization (low power mode and DC-DC regulator...
Hello, i have six buttons on my custom board, these buttons are inited with following code:
(there are pull up resistors present, hence NRF_GPIO_PIN_NOPULL is used)
SEGGER_RTT_printf...
