Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
I am trying to filter an iBeacon sample using a modified version of the central_hr_code.
Changes on the central_hr_code:
Added 128-bit UUID definition:
Added...
Hi,
I am developing a health wearable and want to store biosignal data into flash and then read at some point. I found that the reading process is relative slow as I tested...
Hi,ALL:
I use esb 2.4G liberary,and I found the same kind of produc build of nrf52840,it's radio current consumption is 1.2mA-1.3mA,how can it do it? My project is build...
Hi,
I have 2 nrf52840 DK boards advertising on coded PHY mode. Once connected the connection is updated (using sd_ble_gap_phy_update()) to use 2M mode. No problem in doing...
Hello! I add an attribute array (0x48) for the user cluster. Having problems using the "array" attribute:
1. If you select the data type of 16 or 32 bits, then an alignment...
I have some questions on using the nrfutil dfu ble with the buttonless example.
Should both devices (central and peripheral) be already bonded before starting the DFU process...
Hello,
Using NCS 1.6.1, I would like to use the radio from within a timeslot as suggested in the documentation . However, the MPSL/timeslot sample is quite sparce and only...
Hi,
It's been a few months since I've been developing a new project using the nrf52832. One of the main features is naturally the OTA DFU. During the last months I was able...
Hello,
I noticed that slighly incresed amount of printk output in the B0 bootloader leads to the corrupted debug output.
1st case - I added two printk lines starting with...
Hi,
I was in a strange situation using nrf52832QFAA.
I'm using nRF52832 and nRF52840 evaluation board.
When i download code using Programmer(nRF Connect), the memory...
I want to know the details about integration of Non-IP Data Delivery in NRF9160. Please share implementation details. If you suggest some example code or at commands to look...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to use CC310 with nRF52832. I found the following description in " Cryptography library - nrf_crypto...
Hello,
The VSC plugin is showing squiggles for SPI related nodes which are valid. (compile with no errors)
Here is an example:
Here is the error message
Thank...
Dear Nordic，
We developed a product based on the nRF52833 chip, with an external antenna, 3dBi gain. Use a smartphone to scan the product in the outdoor，the transmission...
The product we are developing will be using a proprietary radio protocol. While in receive or send mode, the radio will either read the Tx data from a buffer via Easy DMA...
