The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Does m_xfer_done need to be set to false before calling nrf_drv_twi_rx? If so, does while (m_xfer_done == false); loop need to be called on every read?
I'm developing a Bluetooth mesh device on a Window 10 machine using Segger Embedded Studio v4.52c on a nRF52832 chip using SDK16.0.0, Mesh SDK 4.1.0 and FreeRTOS.
in the...
Dear all.
I just got nRF52 DK and testing blinky based on KEIL and it works well.
I tried one test, IF BOOT/Reset, and nRF52 PDK is not working after below sequence. ...
Would it be possible at all to add a preset text string to the current advertising data, in an advertising-only module configuration, by changing the logical input of one...
Hi,
I've upgraded my SDK from 15.2 to 17.
After upgrading - I can't connect my device via NFC - it keeps disconnect with NRF_ERROR_RESOURCES .
I've tried to increase...
Hi
My goal is to create a USB HCI firmware that works on any custom board that exposes the USB port of a nRF52840. Based on the requirement for USB HCI it was clear to use...
Hi, I am working on an OTBR, nrf52840 connects to the router through SPI, I want to know how to upgrade 52840 through the router. The router use OpenWRT. p lease give me some...
Hi,
Our devices are getting randomly bricked by updating firmware through mcumgr in Zephyr. It happens on both the nRF91 and nRF52 chips when we run the latest nRF Connect...
It's strange, My nrf52840 can't boot up after power on,unless it was connected to JLINKRTTVIEW, If I disconnected the JLINKRTTVIEW, the device will stop running, Connect again...
Can anyone tell or give a pointer to info about RFCOMM vs. NUS (or any other vendor specific UART emulation service)?
Why are there vendor specific UART emulation services...
Referring to the Nordic message sequence chart in the following link:
https://infocenter.nordicsemi.com/index.jsp
(Software Development Kit -> Previous Versions of nRF5...
Hello!
I use SDK v17 and using the library and example code for the lsm9ds1 sensor.
github.com/.../nRF52-DK-and-LSM9DS1
'lsm9ds1_reg.c', 'lsm9ds1_reg.c' these two files...
Hello!
I am using ble adc scan mode example and successfully tested it with nrfconnect by sending my data from AIN3 . Now i want to send data of ble to raspberry pi bluetooth...
HI
Like to check on the usage of MQTT. We are connecting the nrf9160 to the network in eDRX.
During the interval, we may lose some message due to the lost of connection...
