Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hi,
I use a mcu nRF52840 on a personal card for a project and we are stuck on interruptions: hardware pin and timer. I use the lib "nrfx" for future accounting purposes...
Using NRF_SDH_BLE_OBSERVER in a non-static context doesn't work because the registered variable, and therefore the handler context is lost. How can one register for ble events...
Dear,
I am using nrf9160 DK, we can download hex fiel for boardcontroller
nRF9160 DK board controller firmware
https://www.nordicsemi.com/Software-and-Tools/Development...
Based on the experimental_lpn example if have ported at application (light switch) to work as a low power node.
Everything work fine on the lpn node where i use the generic_onoff_client...
Hello,
I tried to update bootloader on the dongle via DFU, but It failed.
The dongle uses OpenBootloader, so it does not check signature for firmware packages. But the...
Hello,
I'm working on a project where we are doing the following:
Collecting sensor data and storing it in an external SPI flash
Retrieving that sensor data from the...
Hi,
When publishing a message with access_model_publish() the p_message->p_buffer must be remain valid until all retransmissions have completed for loopback message but...
Hello
I want to modify the tx powel level to 4 dbm using sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_adv_handle, 4); after Advertising_Init function.
I could...
Testing with the NRF52840 dongle and the Power Profiler Kit. I see a reading of ~5uA when sleeping without SAADC enabled.
I use this code to enable SAADC
My power...
Environment
- DK 0.8.2 in which SB44 is cut, and P1 and P2 are connected - firmware v1.0.0 - program : asset_tracker - SIM: iBasis
Before updating firmware, asset_tracker...
Hello. Got such a problem. I use nrf52832 Adafruit Feather board. While working with BLE examples (Softdevice and app.), debug via serial works fine. Can see all the text...
Hi,
I have a desig where the space is minimal and I have one nRF52838 and one nRF52840 microcontroller. Is it possible to place them at the same coorinates, but on oposite...
Hello everyone and Good day
I am a fresh graduate and its my first assignment at my job. I have to flash an LED at 1 Hz using NRF52810 BT 5 chip.
There are so many development...
