Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hello,
I am attempting to integrate FOTA (HTTP Application Update) into a Thingy91 project on top of the LTE BLE Gateway example project.
I am on nRF Connect SDK v1.1...
Hi,
How many SPI slaves can I connect to nRF52832 as an SPI master?
I would like to know the maximum number of SPI slaves which can be connected to nRF52832 as an SPI...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hi,
I am using NRF52832 for development without bluetooth SDK, NFC and RTC.
I am using a development board with SPI and a slave device that can communicate normally (using...
Hello,
Most of the outputs and LTE Monitor use by defaut an UART on DK. Problem on custom boards, for cost limitation, UART is not always present. Probe connector is so...
irq init as below:
I use port event, and muti-gpio irqs. Irq gpio connect a sensor`s irq pin.
I detect irq gpio level in irq_Handler(), high level is my need, the...
Hello All.
I Need help ... first time use "nRF52840"
Goal of this project is "record voice with digital mems mic and play that voice using speaker with i2s"
First...
Searching through the forum I found this guide.
"Getting started with Nordic's Secure DFU bootloader, a step by step guide"
https://devzone.nordicsemi.com/nordic/nordic...
SDK 16.0.0
nRF52DK
ble_app_hts example
The ble_srv_is_indication_enabled always return false no matter in the ble_hts_is_indication_enabled function or in the on_cccd_write...
Hi, im usinh SDK V 15.3
i was following the tutorial to add buttonless dfu to my application code
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am a newbie and need some help deciding the path to perform the following requirement. Any help is appreciated.
Requirement:
I have Rigado BMD-350 module currently...
Hi,
I have a nRF52840 DK (PCA10056 v0.9.0). I tried the long range (Coded PHY) but it throws an error and didn't work. I read in nordic forums that the chip revision should...
We are entering a pre-production phase where the contract manufacturer must program dozens of nRF9160 modules, and we would like to offer a command-line method, to simply...
I've just got my toolchain working fine but there's now errors relating to the correct libraries being included. Do I have to have these included by running a "west update...
