I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
I see a number of threads on the Nordic devzone where people are asking about official support for a DFU bootloader that combines BLE and UART for transports. Most...
hello Nordic
i am working with nrf52840, SDK16.0, s140 (maybe i will change softdevice later)
i build a project on the peripheral blinky example, i change the advertising...
Hello,
My application is based on the example "ble_thread_dyn_mtd_coap_cli" (nRF5_SDK_for_Thread_and_Zigbee_v4.1.0). I would like to be able to send large files via Bluetooth...
Setup -
nRF52840-DK
Nordic Connect SDK version 1.5.0
Sample - nrf/samples/peripheral/lpuart
Commented out "uart0" in the board specific overlay
Uncommented console...
Hello i'm trying to compilate the project secure_bootloader_ble_s132 but i'm having issue with micro-ecc.
when i complie on keil the bootloader exemple i get this error...
Hello,
As the question shows, how to add RTC function to a 5340 empty project?
condition
ncs:1.5.0
board: nrf5340dk
I have found a project,but it's 52840.
...
Hello,
My application runs in non-secure mode on the nRF9160, and I would like to disable external access to CPU, RAM and Flash.
I understand this is done by setting the...
Hello
I have board nRF52833 and i have several questions:
1. Is AoA example available ? I would prefer to have example of software for tag and for the localization...
On a custom board based on nrf52840.
We want to implement OTA DFU with radio (not necessarily BLE, e.g Serial 4G Modem)
We already checked the Serial DFU example and made...
Hi
I found the function
in nrf_ble_scan.c.
This decoding looks wrong to me since https://devzone.nordicsemi.com/f/nordic-q-a/27012/how-to-distinguish-between-random...
my gcc version: gcc-arm-none-eabi-9-2019-q4-major
defined in discarded section `.intList' of app/libapp.a(softuarte.cpp.obj)
////////////////////////////////////because...
Hi,
Is it at all possible to use the QSPI interface of nRF5340 to interface a micro SD card? Is sending custom instructions combined with long frames, as suggested here...
Hey Nordic team,
We have ECG/EGM alignment problem over BLE, the peer ble chip use RSL15, they came up with the below algorithm, which do need an API to get connection...
