Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello,
Is there a way I can run JVM on nrf51 or nrf52 series devices? I have been searching the forums and did not find any updates on the same.
Any OS like embedded linux...
Hi,
We are currently in development of an IoT solution using the nRF9160. We are doing a set of EMC tests to ensure electromagnetic compatibility of the device. The test...
Hello,
I am trying to transfer a signal sampled on AN0 (P0.02) at 16kHz via Bluetooth using an ATT MTU of 247 and a 2MBPS PHY speed. The basis project used is examples ...
Hi, I am interested in using the NRF91 in our new products. So far I have modified the Asset_tracker example to send my custom data instead of sending the "sensor data". The...
Hi.
I have a question related to the Zigbee SDK's "On / Off Switch" example.
Studying the example, I cannot understand how to activate the "light_switch_send_on_off" function...
I'm trying to find out if the nRF52840 has the features needed for a new product. We need to be able to do the following from a Windows 7 or 10 program: scan for nearby BLE...
Hello,
I'm working on a project that makes use of both Bluetooth Service UUIDs like BAS and customer Service UUIDs. In the Bluetooth CCSv7 at Part A, Section 1.1, I found...
Hi,
our application is nearly finnished now, but I noticed, that after adding the secure_ble bootloader, the program enters the bootloader at poweron, then enters my application...
Hi, I got the schematic of thingy:92.
Now I have a question about netnabel: IF_SWD.
IF_SWD is connected to three nRF52840 GPIOs.
if the CTRL is high in IF_SWD, IF_SWD...
Hello,
I'm trying to use the USB MSC to show up as a file system, transfer the file into RAM, and send the file via BLE to an Android phone. This is with SDK 15.3 and S140...
Working with Fanstel BT840 module we have discovered that ADC channel VDD reads as zero or produces small mV level result. nRF52840 chip revision on these modules is QIAA...
Hello everyone,
i want to send a 16 Byte datapaket from a peripheral nRF52840 DK to my iPhone. (S140 SoftDevice) Im looking for an example who sends datapakets from peripheral...
Hello everyone,
I have a device with a custom service including 3 characteristics and another device with 4 characteristics (same 3 chars as the first device + 1 new). ...
