I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I am using Fanstel BT832 module based on nRF52832. I am using ' nRF5_SDK_14.2.0_17b948a ' with ' s132_nrf52_5.1.0_softdevice.hex '.
I am using this module as the BLE peripheral...
Hey Dear Nordic Devzone,
Here I am again, it has been a long time. Before I was working with the nRF52840 and Segger Embedded Studio. But as of now the company I am working...
i have programmed a arduino to send data(int value) on tx ,rx pin .How shoul i set up the nrf52 (the pin no of rxd and txd on nrf are p0.6 and p0.8).Which example should i...
Hi,
I'm looking into the reliability of the BLE connection from one nrf52 to another nrf52. I'm looking to understand a few things.
Once a connection is established...
In both the SDK and production specification (PS 1.4) it is noted that the TIMER (Timer / counter) peripheral in 'COUNTER' mode (0x01) is deprecated.
For implementing a...
In my current case there is a relay node to which want to send RSSI values of beacons nearby and then relay the same information across other relay nodes in the network, So...
what is the problem of "ERROR Failed to open nrfjprog: Error occured when open device long term. Errorcode: CouldNotLoadDLL (0x3)" , when i use the nRF Connect.
the version...
Hi,
How can we receive more than 20 bytes of data from the phone? We are using s132 and SDK 12.3. I know how to send more than 20 bytes of data from the NRF52 to the phone...
I am a newbie to Nordic chips and tools and new to bluetooth. My company is doing a BLE sensor. We have a prototype board ready and I am trying to do some firmware for it...
Hi I have tried the light demo example, where I do not understand the difference between "reply_Status" and "publish_State" on the server, then someone can explain the difference...
I am currently working with an NRF51822 and managed to change the TWI frequency to 400kHz in the twi_hw_master (this worked, I can see it on the oscilloscope). I commented...
I'm trying to upload via DFU from one nRF52832 to another nRF52832
I use SDK 14.1
First I want to enable CCCD at the master side.
static uint32_t cccd_configure(uint16_t...
Dear Sirs,
We are evaluating nRF52840 now, How far is the maximum range it can reach while keeping the data rate at 2Mbps if we use two nRF52840 for point-to-point communication...
