According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
When I just plug the USB cable on the board I get a GPIO high voltage of 3V. But when I also put +5V on the external supply pins, the GPIO high voltages are 4.5 V. Is this...
Hi,
We are using nrf52832 board with sdk14.0. We are facing two issues:
Our use case is to send the data continuously when the notification is enable and stop...
The Bluetooth pairing is not working properly. I am developing the Application based on Bluetooth pairing with UART. Here I have included my concept and Program.Help me out...
Hi to everyone!
I have been getting the output of NRF_LOG_INFO functions through RTT in J-Link RTT Viewer terminal. The code has been executing in nRF52832DK.
Now I...
I have set up an nrf cloud and can control the led on pca10056 using the nrfcloud so configuring the gpio(pin no 7(Port P0.7))is becoming a problem.Can u provide me with a...
Hello,
I bought a nordic/wellcore ibeacon (nrf51822) to experiment. I want to enable all the features and would like to know what value to assign to the temparature enable...
Hello, i am using SDK12.2.0 and SD s130 on a nRF51822 (AC) and i am trying to add an external interrupt on a pin in the cscs ble_peripheral example. The code i am using (and...
Hi
We are using sdk version 12.2.0 and trying to change it to sdk 14.0.0. However, when I measured the power while converting the code, ppk confirmed that the sdk 14.0...
Hi all,
I'm using SD S132 v5.0.0 with SDK 14.0.
I'm testing now the BL buttonless DFU (and later the SD buttonless DFU) after working well with the app buttonless DFU...
I've implemented monitor mode debugging as described here and it works great. When I get a hard fault, it doesn't break in the IDE anymore. So it appears to be running fine...
I can connect the kit to the nrf cloud and even add the device to the gateway but i cannot switch on and off the leds.Where is the source code for the nrfcloud example?I cannot...
Hi all,
I recently encounter this strange issue that I couldn't understand. My code works perfectly fine during debugging on all 52832 chips, but freezes without response...
For nrf52832, I use pstorage to set 254 blocks with 20 byte of each block, that will use near 5 pages.
now I fail to clear data all block together. pstorage_clear( &block_base_handle...
Using an nRF52832 with SDK 14.0.0, S132 SoftDevice
We are able to connect to the device with an iOS/Android phone just fine.
Upon disconnecting, a second phone is not...
