I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi
I add the fstorage to ble_app_uart on the SDK v14.1 to work on nRF52810. After fstorage initialization, I could write data to flash.
However, if I write the data...
Hi, I'm testing the light control example from Mesh SDK 0.10.1.
Although I have received an answer about the future plans of mobile Mesh SDK from developer Hung Bui that...
Hi,
I have some data which i want to send from nrf51-dk to ESP8266 . i have tried Ble UART central example to write data serially but doesn't achieve any result. I have also...
I have 2 Channels with SAADC taking samples. They are configured to respond to BLE characteristics that have read and notify properties, each channel has its own characteristic...
Hi,
As in the Product Specification of nRF52, pin number 9 and 10 are configured as NFC pins. However, this setup is conflicted with our pin mapping for other sensors in...
I am trying to store a small amount of data on the nRF52832 with the FDS module.
I followed the following code found in another question:
devzone.nordicsemi.com/.../...
Hi,
We are currently migrating our codebase from SDK 13 to SDK 14 for NRF52832 based board. One major difference we see is that SPI transfer completion callbacks are not...
Hi Dear Nordic!
We have prepared 200 pieces of PCB (used nRF52840) to pre-test our Product.
Now we are waiting for nRF52840 IC to solder.
Is it possible to buy ~...
Hello,
I've just found the Zephyr project which provides very interesting features and many questions are rising in my mind, but I don't know if this is the correct place...
I want use the NRF52832's NFC Tag in a bracelet. I need to know when the battery of the bracelect
is out, can the NRF52832's NFC Tag still be readable? Like the UID of the...
Hi
I add code in nrf5_SDK_for_Mesh_v0.10.0-Alpha_src, and when it run the follow code
and the ret_code is 4, I get information from the follow code
it is NRF_ERROR_NO_MEM...
Hi everyone !
I'm working with nRF 52840. I've downloaded softDevice s140 using Keil. Afterwards, I selected the target to nRF52840_xxaa and then build the project of Heart...
Not sure I understand the sentence. Do you guys mean "enabled"?
PSEL.SCK, PSEL.MOSI and PSEL.MISO must
only be configured when the SPI master
is disabled.
infocenter...
