Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have trouble programming the PDK using nrfjprog. I can flash the program fine using Segger Embedded Studio but it doesn't appear to be working using nrfjprog.
Here are...
When using ble_app_uart, I set the advertising timeout to 10s, but after the timeout did not enter sleep, but automatically reset,my judgment is based on the terminal to send...
Hi
I have run this example code
nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject
when I operate...
I want to reprogram a nRF51822 xxAC device on a existing product.
I have a J-Link (SEGGER) device with latest firmware.
I'm running the SEGGER J-Flash V6.20e utility.
I...
Hello,
I have constructed a custom board with nRF52832 and MPU9250 on it.
I have flashed the program for reading battery service, temperature service and MPU9250 readings...
I followed the tutorial on devzone.nordicsemi.com/.../ to use Eclipse, GCC and GNU Debugger.
I encountered an error after the successful build (with key symbol) with CDT...
Hello,
I purchased nrf51822 module and i want to use s130 sdk for my project.
But when i have look over using keil i found that it requires jlink debugger or jtag debugger...
I am studying about developing a simple BLE 6LoWPAN network. My proposed topology is mentioned below:
internet - - - - - - - - - BLE1 - - - - - - - - - BLE2
| \
...
Hello,
As we can see, the mesh stack is a totally new stack which is independent of traditional BLE stack. Could you please explain why to design like this?
I found there...
Hi, I'm deeply interested about the Nordic's PCA20014; a.k.a solar beacon .
This HW uses
Amorton AM-1417CA solar cell, 1.5V, 12.5uA at FL-200lux
2 channel...
Hi,
I have run into a problem with the nRF sniffer. I used it in late May and early June to debug a BLE connection between a nRF-DK and a HTC Desire 610 and it worked fine...
Hello,
I am trying to communicate urart with nrf52840 and other devices.
But there was a problem.
You can transfer data from the nrf52840 to another device, but if...
Hello,
I need to connect an event handler (i.e. a function) to two NRF_RADIO events:
-NRF_RADIO->EVENTS_ADDRESS
-NRF_RADIO->EVENTS_READY
I know I should use the NRF_RADIO...
Hello ,
I can read the rssi value after the connection is established.
case BLE_GAP_EVT_CONNECTED:
APPL_LOG("Connected to target\r\n");
err_code = bsp_indication_set...
On this question it is said:
"Error code 0x3201 means BLE_ERROR_GAP_DISCOVERABLE_WITH_WHITELIST: Use of Whitelist not permitted with discoverable advertising ."
Why does...
