hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi all,
recently I tried sd8.0 and i used the example "ble_app_hrs".
the strange thing is in my phone i can see device advertising but cannot connect to it successfully...
I tried to use this example with a nRF51422 and the board of N5 Starter Kit of Dynastream. I adjust all to make it works fine: custom_board and so on.. And I used the Soft...
From SDK 7.2, we have the following definitions:
components\drivers_nrf\pstorage\config\pstorage_platform.h
typedef uint16_t pstorage_size_t; /** Size of length and...
There was something in the webcast yesterday about a Nordic nRF52 roadshow/tech tour/worldwide series of events.
I hunted around the nordicsemi site but didn't find anything...
hi,
i am working on ble project where i am trying to develop a project with master(mobile phone)-bridge(acting as master and slave,nrf board)-slave(nrf board) .i use the...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off all modules except the RTC timer.
So, after shutting down the radio...
Hi,
How could i implement Just work pairing method in my "ble central and peripheral" example. I modified project to suit my need, and everything works fine, untill i try...
I am working on a ble project ,'ble_central_and_peripheral",s130.In this project the device acts as master and slave. It connects to the slave only if the address is predefined...
I may be missing something. I am trying to generate a square wave from a GPIO pin in a BLE application (SoftDevice 8.0). I tried libraries (nrf_pwm.c and nrf_pwm.h) in this...
Why does the nRF52 only have +4dB output when most competitor chips are atleast +6dB (some up to +10dB). I understand that the RX has been improved by 3dB for a better overall...
Is there a way to know that there is no more data being received via UART?
One solution is, of course, to start a timer every time a byte is received via uart_evt_handler...
I am using read characteristic to read data from from a characteristic. The characteristics range from 2 bytes to 32 bytes in length. The time to read the data using IOS,...
For those of us who were not invited to Norway to try the nRF52 over the next two days....
When and how can we get our hands on a nRF52 development kit?
For example, ble_advdata_set() wants to insert company identifier and a "00" in the last byte of the response packet. Are these required, and if not, how to use the ble_advdata_set...
