Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
It's this will be work?
// Initialize the Bond Manager.
bond_init_data.flash_page_num_bond = FLASH_PAGE_BOND;
bond_init_data.flash_page_num_sys_attr = FLASH_PAGE_SYS_ATTR;...
Hello：
I need to ask you after the next programmed into how this routine testing 。（nrf51_sdk_v4_4_2_3355\nrf51822\Board\nrf6310\ble\ble_app_alert_notification ） The iphone...
Dear Developer Zone,
I am working with nRF51822 and IOS.
My device can only be connected to one central, so to one iPhone. To refuse connection from others centrals...
Hi all,
I've got some questions about the DFU OTA Nordic example (nRFToolbox):
What is available full stack update or profile update?
Firmware flow, does it need to...
Hi Folks,
I'm running into a problem with the pipes on my nRF8001. After I issue a Connect (0x0F) command, I receive:
CommandResponseEvent (0x84)
ConnectedEvent...
We have setup the RX and TX modes for ANT+ in Advanced Burst mode.
The setter function works (can confirm that by using sd_ant_adv_burst_config_set());
However when...
Hello,
I understand that S310 stack currently supports Ant+ and BLE peripheral. Is there any way to incorporate BLE central (S120) and Ant+ (S210) stacks on the same device...
Hi,
I have nexus 4 smart phone with nRF Master Control Panel application. How can i change the IO capability of the master device? I need to test the pairing process (passkey...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi There,
We are using two microprocessors in our project is kind of activity tracker which is stm32l (M3) with accelerometer, temprature sensor and SPI flash connected...
I'd like to start developing with the nRF51822, and have found the two kits supplied by Nordic, the nRF51822 Evaluation Kit and the nRF51822 Development Kit. What's the difference...
I am being told by a RF test lab that I need to provide a sample which has the following modes:
BLE "with modulation"
BLE "without modulation"
ANT+ "with modulation"
ANT...
Hi all,
When I test the UART demo progrem, I cut off the power supply of the board,but the RX pin is still connected to the PC TX pin,and I measures a voltage on the VDD...
