the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
I have a production device which I have soldered an SWD connection from a Keil project via the nrf51822 DK (port 20). I can flash code to this production device, but I cannot...
I'm using a SPI with a circular buffer so i need to have an interrupt with low latency that reset the RXD.PTR when the buffer is full.
The SPI is used for communicating...
Since Zephyr’s official BLE sample code, his BLE central only supports one central to one peripheral So I refer to the BLE central multulink officially provided by nordic...
HI ,
My name is MOHAMED ALI SAIDANE from Tunisia , i've been working on my project of the last year eduction , i'm interresting about the concept of the module NRF24l01...
We are using a custom ARM board which runs Linux and has a UART interface to a nRF9160.
I'm not how to phrase this exactly so I will just describe what I would like to do...
Hi,
I am using nrf51 DK and MDK is keil5
SDK : nRF5_SDK_12.3.0_d7731ad
softdevice : S130.
when i load the code nRF5_SDK_12.3.0_d7731ad\examples\peripheral\twi_sensor...
I have used light_Switch example from nrf mesh sdk nrf5_SDK_for_Mesh_v4.2.0_src I like to get the client source address in nrf_switch_server what should I need to modify to...
hello Nordic
i am using nrf 52840 dev kit, sdk 16.0
i want to make a sampling of 2 channels at 32MHz rate. the data shell be passed to RAM via easyDMA, after every 4...
Hi, I try to change my MAC address, but return error code 8.
check error code 8 is :
So I try set the mac address after ble connected. and the function sd_ble_gap_addr_set...
I'm trying to drive LEDs using PWM on Thingy:52 and Zephyr OS. It works when I connect external diodes to GPIOs, but built-in LEDs are connected to I/O expander instead. ...
Hello,
I have an Android application that sends and receive data from a nrf52832 peripheral.
During a test for our device using a nrf52932 chip, 2.4GHZ noise is emitted...
Hi. I bought the BM832E development board and have not yet ordered the DK board.
It says that arduino uno rev 3 is compatible with it. Does this mean I can plug my arduino...
Hello,
I am using nRF52 DK development board. I'm having a problem when I load simple blink example . I am getting an error message Error: Flash Download failed -...
Hi all!
Im still new to this and I'm trying to help a friend with a PCB design. We are using the nrf52832 and recreating the design from the reference circuit given in the...
I am trying to Compiling ‘ble_advertising.c’ and get 'NRF_EVT_FLASH_OPERATION_SUCCESS' undeclared (first use in this function).
This declaretion is already in the nrf_soc...
