Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I am developing a NIR (Near-Infrared) product using nRF52810. I use 15.3 for SDK and S112 for Softdevice. I implemented ADC (saadc) function based on ble_app_uart.
I have...
Hi everybody,
I been experimenting with the HID over GATT example (mouse), and I am trying to use more than 3 report IDs. When I used only 3 there's no problem. But when...
Hello DevZone,
SDK 15.0.0. SD132 PCA10040
SPI settings : Mode 0, MSB first, 125kbps, orc = 0
I am trying to get NFC communication between two dev kits, one using the...
Hi,
is there a possibility to tune the external xtal (lfxo) or the rtc?
In other microcontrollers there is a possibility to trim, for exampe the rtc ignores one or more...
Hi teams,
I have build custom board connected to ethernet via ENC28J60 ethernet controller.
It uses SPI communication with ENC28J60, but some strange behaviour during...
hello
i am using nrf52832 with pwm driver (working with ble and s132 if it metters)
i need to control 4 different motors speed via pwm, since there can be only 3 instances...
Hi
I have implemented a scannable advertising on nRF51822, s130, SDK12,
I can see it's working by reading the scannable information on nRC Connect, however,
on the sniffer...
Hallo,
I have a question reading the datasheet. It states:
" If a regulator is only to be used in LDO mode, the inductor for this regulator is not needed. "
I want to...
Hello,
i'm trying to understand how nrf52 and softdevice work to use it in the future, i'm working on STM32 and i have my own RTOS, i try to appropriate the platform by...
I received my NRF52840 dongles and downloaded SDK 16.0.0 and SES 4.52c. I found some old documentation that said how to convert ble_app_blinky to the dongle but then exploring...
Hi,
I have nRF52840 Dongle(PCA10059), I try to develop on the nRF Connect Desktop. But this dongle can't update firmware on the nRF connect desktop.
My operation below...
I’m using the latest version of the modem 1.2.0 and sdk v1.2.0
For the most part AWS FOTA seems to be functioning.
However it will start the FOTA job and hang and fail...
Hi everyone,
I need to set up a timer using the RTC. The default function that converts ms to ticks APP_TIMER_TICKS() accepts only milliseconds. So, I wrote my own conversion...
I want to interface Client Sensor over UART in light_switch_client code. Can you please give me the idea,how to do it.
I am using Mesh_V4.0 and SDK 16.0
