The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I am trying to read the data of an MQ-6 sensor, which is its gas sensor, but the data I receive is not from the reading by the values it shows, if you know how to do it or...
Hi,
When the bootloader address resolves to something invalid, fds_init will hardfault. I think it should have some check and return a nice error code instead.
See an...
Hi,
I want to disable all four buttons to my rigado bmd 300 evaluation kit (pca10040 is the board config. the same as nrf52 DK ) in project ble_app_uart
I have tried to...
I'm powering an nrf52810 with a 3.3V regulator. I understand the internal LDO powers the system at 1.3 V. Are the GPIO pins and other peripheral devices outputting 3.3V for...
Hi
When I select the Generic Level server model and try to bind the app key I get an invalid model Error. I am using the nRF Mesh android app.
This might be relevant or...
Dear Nordic Support,
I am using ble_nus service on nRF52840 (BMD-340-A-R) + Raspberry Pi 3B+ ( https://github.com/IanHarvey/bluepy ). The nRF52840 is the peripheral and...
Hi,
I would like to know the I2C bus capacitance for the nrf52840. Do someone have the information please ?
My slave components are compliant for 400Khz and VDD is 3.3V...
I have gone through the tutorial on mesh experimental dimming and I was able to provision the BLE nodes, contol and dim the LED1 on the evaluation module with RTT viewer....
Hello everyone,
We are having a problem with the DFU function in our custom iOS app.
We are using DFU library version 4.5.1.
After updating SoftDevice and Bootloader...
I'm using the nRF52840 DK to develop my application using FreeRTOS while trying to achieve the lowest possible consumption. I'm having some issues so I went back to the ble_app_hrs_freertos_pca10056_s140...
hi
i use the example flashwriting in nRF5_SDK_15.3.0_59ac345, i set a table at 0xfd000:
// ProgramSection alignment="4" keep="Yes" load="yes" name=".tabletest" address_symbol...
Hello, I am using nRF9160 PCA10090 DK. I want to make my board as central device and scan for all nearby BLE devices and display its rrsi value and device id on a terminal...
Hi,
Recently, I was trying to established an application based on ble_app_hrs with PCA10028.
The MCU I used is nRF51822_xxac (256KB), S130 for softdevice and the SDK is...
