the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Dear Nordic Support Team,
I'm working on a BT Mesh implementation and came across a problem with the proxy enable / disable feature.
Disabling the proxy function doesn...
Hi all, I'm working on making mesh sdk work with peripheral uart example. I tried to merge peripheral uart example (nRF5_SDK_15.0.0_a53641a) into proxy_server example (Mesh...
Hi,
I was into the working of bluetooth mesh. I was wondering if it is possible to configure a bluetooth mesh network with a smart phone acting as a provisioner and by any...
My aim is to establish communication via nRF52840 dongles. This means if I connect mobile phones to the dongle and the data sent by one mobile phone should be received by...
Hi
Does the nRF52840 and 52832 support automatic gain control (AGC) for for BLE?
See this Ti post which suggests AGC is not used for BLE
http://e2e.ti.com/support...
I have recently migrated from SDK 15.0 to 15.2 and are experiencing problems with my code.
I have a nRF52840DK and have attached two accelerometers to this board. I am able...
Hi,
I'm currently working on achieving BLE NUS + ESB UART concurrent implementation via timeslot API, by referring to the example here . I have ported it to utilize SDK15...
Hello,
I'm using nRF5 SDK with version 15, nRF52832 IC and softdevice s132. I need to save hold the data in the ram even in sleep mode. I'm using the below code. However...
How can I return my nRF52840 DK to its out of box condition (firmware, demo) so that I can turn the device over to a colleague and let them run through the getting started...
1. SDK version : nRF5_SDK_15.0.0
2. Platform : nRF52832
3. Purpose: NUS service with example ble_app_hrs_rscs_relay.
4. Problem : NUS device connection only success...
Using a Peripheral set in Central mode and write then read data back in the Dongle nRF5240 set in Server Mode.
Once connected and exchange MTU (extended) I write and then...
Hi Developers,
I am exploring the light switch examples, client, server and provisioner, every time a node is provisioned it uses a unicast address, what if I want to use...
Hi all,
In our project we are using nrf52810, SDK 15.0.0 and ble_app_uart.c example.
We are using our custom board in which MCU is communicating with BLE through wired...
Hello,
So i found this code from one of the earlier post which combines the saadc example with ble_app_uart example to make analog values from the analog pins to be sent...
