Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hello Nordic Team,
After setting connection parameters in accordance with Apple BLE design guidelines the BLE throughput has been significantly decreased.
My parameters...
Hello,
If I use the nRF51822 with 128KB ROM and I connect to a external flash via SPI.
The SoftDevice and bootloader are stored in the internal 128K ROM.
Is it possible...
Using GATT characteristic writes to transfer data is slow.Is there a cleaner and/or faster way to do faster OTA upgrade?
Also I wanted to upgrade firmware without affecting...
I have set up a 6lowpan test environment and could control the led3 and led4. could u please provide me with a code to read value at p0.01. i want to connect a temperature...
I directly connect GPIO pin with 24ohm resistor as follows.
And I set GPIO pin as high drive,
NRF_GPIO->PIN_CNF[MY_PIN_NO] |=
(GPIO_PIN_CNF_DRIVE_H0H1 << GPIO_PIN_CNF_DRIVE_Pos...
hello ,i use SDK9.0 ANCS project.when I paired it ,it can work normal. it can recive QQ,wechat,message and so on. but when I paired many times, it will be SystemReset.
...
Hi
I am trying to make an activity tracker with very low power conumption with the nrf52. The Idea is to count interrupts from an accelerometer thtat are generated if the...
Hi
I'm testing Buttonless DFU.
I use SDK 12.2.0 , NRF52 and S132.
I succeeded in entering DFU in Master Control Panel (PC application).
I want to do it even on iOS....
Hello,
I recently finished up the NRF51822 pcb board that I plan on getting printed. I posted my board before and have fixed the problems another user specified.
I used...
Hello,
is it enough to call NVIC_SystemReset() after I flashed a board so that it returns to lower power consumption? Or do I have to pull out the battery?
Marius
I hope to trigger notification from Bluetooth module into Master Control Panel. I had enabled notification/indication = true. However, when I pressed the button on my module...
Hai
i am able to store one array in flash memmory of nrf51822. but i need to save more than one set of data into flash and retrieve it separately.
how can i save more...
Hello Everyone
Is there any example code which uses indication property. Application nAn-36 uses notification property and as far as i read and understood about indication...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
