The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
am trying to use SPI with nRF 52832.
So I implemented spi_master.c which was used in nRF 51822.
However, it does not move hard.
The length set by SCLK does not come out...
Hi,
So I'm fairly new to programming the nrf51822 and using the Nordic platform.
I'm currently using the nrf51822 Waveshare DK. I have setup JLink5.1.2, nrf5_MDK_8_5_0...
Hello,
I am using SD 130 on nRF5 with SDK V12.1.0.
I want to write to a characteristic using the android debug app (nrf connect).
This is my code for the characteristic...
Greetings,
As mentioned in this blog post, GCC compiler -flto flag isn't mysteriously present since SDK 9.
devzone.nordicsemi.com/.../
Any specific reason for this...
Hello,
I use a SparkFun programmer to flash a nRF52832, once I flash my board (with the program below), I type in my terminal : "JLinkExe -device nRF52 -speed 4000 -if SWD...
I have many peripherals, dealing with each of them individually will be very ineffective. The peripheral has no buttons, but it has a display.
Questions :
For security...
Hi,
In my application of interfacing SD card with nrf52, I am using SAADC to sample the input signal at 1000 samples per seconds. These samples I am combining in 84 packets...
I have set up ble_app_uart along with gpiote and spi. When I first trigger the GPIOTE event the MCU is supposed to go to sleep after, but it seems to keep running in the main...
Hi Everybody!
I'm trying to integrate a buttonless dfu into my application but I'm not able to get even the provided example in SDK 12.2.0 "experimental_ble_app_buttonless_dfu...
Hi,
When calling app_sched_event_put inside the same hanler i am exit to main for(;;)
The main loop
for (;;)
{
nrf_drv_wdt_channel_feed(m_channel_id);
app_sched_execute...
Hi,
What is the valid configuration for SAADC with oversampling for nrf52 sdl12.2
I try
SAADC config
SAADC_CONFIG_OVERSAMPLE 4
nrf_saadc_channel_config_t channel_config...
Dear Nordic Team,
Thanks for supporting.
I have a nRF51822 Board (PCA10028) and Also i have arduino code for reabear from ( github.com/.../nRF51822-Arduino )this link...
Hi, all great guys,
We are using NRF51822 as the MCU,and met a very strange problem about the current consumption in our application. Normally,the lowest standby current...
Hi.
I'm new to Nordic BLE devices. Using the nrf51-DK.
I have a peripheral device (non-Nordic) which I want to connect to from a Nordic central (S130) using the public address...
Hello, I want to change mode from radio test example from button input.
How can I use the gpiote for mode change from button input.
I only want to use modulated and unmodulated...
