The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello,
I'm trying to recreate the PWM_library example from the v.11 SDK in a new file in Keil. I have compared the debug settings in my project to the debug settings to...
Hi there,
I am following the thread to use JlinkExe and JlinkRTTClient. I encountered a situation which i don't understand.
After running JlinkExe (go to the folder...
Hello,
I am trying to remake an nrf52 project in Keil and ran into a problem regarding stdint.h. There is already an "include <stdint.h>" statement and Keil has not reported...
Hi,
I am testing the NUS using the UART example in the SDK11 with the PCA10040 board.
Since I want to achieve the maximum speed of transmission I used the FIFO buffer...
I am having issues waking up nRF52 with s132 using the RTC interrupt. The same code is used on nRF51 with s130 and does not show this behavior.
The RTC is configured and...
Hi,
is it possible to have the same configuration as in the example ble_central_and_peripheral but with ant+ as peripheral (on nRF52)?
Thank you for your attention
I am doing externally triggered SPIM transfer on the Nrf52 using PPI.
I found that the NRF_SPIM_TASK_SUSPEND is a very power hungry operation as SPI suspend waits for the...
Hello
I have a nRF52-DK and I am trying to programme an external designed by myself but this one contains the nRF51422 chip. I am using nRFGO Studio to upload the .HEX...
I consider using " nRF OpenMesh " to implement my project.
But, I have no idea bout what's the throughput of it.
Anyone has an idea?
I find the max. content of advertisement...
Hello, I'm trying to make two nRF52832 connect to each other on their own. Currently, it seems that the ble addresses are reversed when printed by ble_gap_addr_print in different...
Hello,
I'm looking for a solution to achieve best possible resolution timestamps of received advertising packets for BLE. Is there any specific chip that you would recommend...
Hi there!
I searched the forum and didn't find any clear answer.
nrf52 programming pins are SWDIO and SWDCLK and chip can be programmed.
When nrf52 is part of a pcb...
HI,
I am trying to Port the BLE BEACON source code of PCA 20006 to PCA 10028 EK.
I have changed the IROM settings.
I have initialized the soft device handler to NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I am trying to understand how can I have a running counter based on the low power 32.768 KHz oscilator that does not trigger any timeout interrupts (I am using the soft...
