Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hello,
I have added a timer to my code, which I need to be of 1ms. The handler of the timer is correctly called when the timer is 5ms or above. However, if I change it...
Hello,
After searching in forum, I understood that we cannot debug application with softdevice unless PRIMASK bit is set.
But in my application there is a requirement...
Hi Nordic
I am using GZLL to develop a prototype whereby data from sensors will be transferred to a Computer in a Wireless sensor network.
The idea is, when data are requested...
Dear all,
we want to use a nRF52837 for a developement project we are planning. We have been asking ourselves on which functional level the alpha Softdevice S132 for the...
Hello, i analyze the device manager routine (device_manager_peripheral.c) and in BLE_GAP_EVT_CONNECTED case you checking containing the device address in bonded table.
My...
I am working with nRF51822 beacons and an iOS 9 application that I am developing. I am testing on an iPhone 6. My application uses the CLLocationManager's beacon ranging functionality...
Hi,
I want to use the whole payload of the advertising packet. I decided to use the manufacturer specific data. BUt I cant´use the whole payload by myself. I get this payload...
dear all：
I use the spi slave mode. i have a question,pls help me.thanks.the questions as follow:
I want to distinguish instruction type, and then reply to the corresponding...
Hello,
I am working on nrf51822 SDK 9.0 and softdevice 8.0 . I got the application note to create a custom profile for SDK 5.2.0 and softdevice 6.0.0 in nAN-36_v1.1 . ...
Hi: We develop our program based on (nrf51822 QFAAG0 1403AL), I found a serious problem that our new IC is (nrf51822 QFAAG2 1415AF), and the old program can't run on it any...
Not sure where to post this...
but there's a minor bug in components/toolchain/system_nrf52.c, where NRF_UICR->PSELRESET[0] is being checked twice to see if a reset pin...
While ota dfu via nrf toolbox android app, it sends wrong (0x15918) image size in start packet, and also bootloader starts writing softdevice image at address DFU_BANK_0_REGION_START...
Hi! I want to make a BLE network with 1 master (nRF51-DK) and multiples slaves (nRF51-dongle). I`ll send differents commands from master to slaves. This is for home automation...
Hello,
I am writing an application using SDK version 8.1 where I have a pin using the PORT event in nrf_drv_gpiote library. I have a need to disable the event temporarily...
