I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
hi. As I know, if I want to change my nRF8001 Device name, I have to check "Over the air" and "From application controller with pipe" boxes in nRFGO Studio. in this case,...
Hi,
I want to make sure that the nRF52832 can start working (turn on) with a 1.8V power supply. Therefore I went to check the default value of POFCON register, in which...
Hi,
I got the PWM example code working, but I need only 3 PWM pulses (14usec on time and 34 usec off time). How do I configure the PWM pins to output just 'n' cycles? thanks...
Hello,
I have downloaded the nrf52 sdk (version 0.9.2) and following the steps listed here: infocenter.nordicsemi.com/index.jsp , to run the blinky led example. However,...
hi, i'm looking for layout and schematic (altium ver.) of attatched nrf module (nrf 51822 BLE).
how ans where can i get this ????
actually i need the imformation...
Hi,
For each sdk version there is a release note of known bugs which is good :-)
I guess it lists the bugs known at the time of the release of the sdk.
Are these posts...
Hello,
I am developing in NRF51 with gazelle communication. I specify in project setting (in IRAM) to use full RAM of my nRF51, and use MicroLib. My last working application...
Hi,
I wonder if anyone knows any free C++ compilers for nRF52. I tried the mbed but it is not fully supported for nRF52.
The regular GNU GCC: arm-none-eabi-gcc works perfectly...
We are working on a project using the nrf52832 (SoftDevice s332 v0.9.1alpha, nRF5 SDK 11.0.0) in which we build a library as a hex file and and load it into a known flash...
Hi Guys,
I am using Bluez 5.39 on Ubuntu 14-04 acts a the peripheral by running "example-gatt-server" which creates 3 services and serveral characteristics within it. ...
In a project, I know the Bluetooth address from the machine, also know the phone's address. I want to let Bluetooth devices from the computer and mobile phone side of Bluetooth...
When I use the example of ble_app_uart(SDK : nRF5_SDK_11.0.0_89a8197) to measure data througput ,I find that i cannot get the complete packet of 20 bytes.
The operation is...
ble_ant_app_hrm.rar Hi!!
I want to design dual mode(BLE UART +ANT) but unfortunately I can not built it well.
Can anyone tell me what kind of function or parameter? I based...
Hello,
I am using the nRF51 dongle to try to observe the packets sent between two soft devices. I have inserted the dongle into one of my PC's USB drives and am holding...
