There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
We're working on getting our nRF52 app working with buttonless OTA updates and the bootloader. OTA works fine with the example bootloader, but when we extend our application...
Hi, I Converted experimental dual bank signed bootloader into single bank signed bootloader and it uploads the new firmware successfully but the problem I got is it erases...
I have an application programed on the nRF 52DK (PCA10040). Its a UART communication to a distance sensor. The Problem is, that I cant send anything from the uC to the Sensor...
Hello,
I just run in following issue. I try to configure an UART to send some bytes. To check the configuration, I just let the program loop, after the sending. Attached...
Hi all! I have a smart beacon kit rev 1, with s110 on it (the latest firmware available). I am using the RTC with the 32 kHz crystal (50ppm) to trigger an ADC conversion every...
After releasing reset to the nRF51, its UART is responding with
RX: A4 1 6F 1 CB
Further requests for things like capabilities, etc go ignored, and opening a working...
hi all,
i cant able to find the version 11 softdevice hex file. can you please send the link.
and can i use the version 8 softdevice for version 11?
-Thanks in adv...
In the migration guide, I can read: "Clearing an interrupt event may not take effect immediately."
And an example of required code is given as:
NRF_TIMER0->EVENTS_COMPARE...
I'm creating a PC application using the ble windows driver by nordic, i cannot implement white list. I ported my code on the firmware & it works.
Is this a limitation of...
When i follow the Getting Started guide for the nRF52 DK at point 5 the led (led 1) does not start pulsating and I do not get contact with my phone. I tried to upload the...
I am trying to make communication between STM32F407ZET6 and NRF52832 chipsets using an SPI interface.
One is master and another is slave. If I take NRF chip as master,...
I am noticing a problem with pstorage_raw_clear when called in the DFU code. My problem is this: when attempting to update an application, if the application is too large...
HI, I have a remote control with nRF24L01. It was talking with Gen1(uses nRF24L01) product via ESB. Now, I am developing Gen2 product*using nRF51822xxaa) and I need to support...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. The bootloader project based on example from SDK11, now just an external...
Hello:
It appears (although I am not 100% certain) that there is a small delay (< 10 usecs) between EVENTS_END in the radio and MICSTATUS in the CCM. I believe I have read...
