I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi
I want to use nrf52 LATCH register.
I can see the correct bit set in the register, but I am unable to clear this bit.
I have tried NRF_P0->LATCH =0xFFFFFFFF; for my...
Hello
I am doing a PCB design using nRF51422-QFAC chip. I did based on nRF51-DK but now I would like to change for a SMD antenna (2450AT18A100 from Johanson Tech.) instead...
Hi ,
I am working on one application in which i need to stream the ADC values over BLE to the mobile App. This should happen at very high rate i.e. 1000 samples per seconds...
Hello,
I'm trying to do something like ibeacon where data is pushed to any device listening, but I want to update the advertising data from raspberry pi 3 since it supports...
Hello,
I am working on an application where the nRF51 acts as both central and peripheral. The device is in permanent connection as peripheral while scanning for other devices...
Hi
can ESB be considered RealTime transfer as soon as it has it's timeslot?
Outline of use-case:
Device advertises existenace on BLE
If there is data waiting...
I am trying to implement a REQ line protocol over GPIO to signal to the Master when it is ok to receive data. Basically, I want to pull the REQ line high when the nrf51 has...
Hello,
Ble spec says that "new alert" characteristic - field: "category ID" can have 1 or 2 bytes.
here
But it seems in your struct you let it have only 1B.
typedef...
Hi,
I have ordered a PCB using the reference schematic for NRF51422 user guide.
I wanted to know whether the schematic has the required antenna design or I need to add...
Hi All,
I have a basic question about advertsing data, more precisely about device's address.
I try to disable in my advertising data, the address field but it doesn't...
Hi I followed the Nordic UART example code to read and write characteristics to a Nordic S110 nRf51822 device.
My code is the same as in writeRxcharacteristic but when...
When I'm single stepping my nRF52 application in Keil with a BLE connection I always get the softdevice_fault_handler called.
I'm using SD 132, v2.0.0 and the the parameters...
What is the maximum clk frequency that can be output on a gpio for the nRF52832 ? I want the nRF52832 to output a clk signal on any of the gpios to an external module, and...
Can anyone please suggest a simple example on initializing SAADC Driver on one pin and do a simple blocking ADC read?
Sorry for a very broad question - but rather to ask...
