Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi,
I developed an application with Nrf51822 with some bonding need.
No problem with android or using the dongle, but using iOs systems it happens that after a random attempt...
When I add a GATTC in S110-V6.0.0 ,my GATTS stops working,the NRF Master control panle retern ERROR(0x85):GATT internal ERROR Error(0x85):GATT ERROR .Can S110-V6.0.0 run GATTC...
The note on the IoT softdevice says:
"This SoftDevice is a technology prototype only. Therefore, it should never be used in production."
Will there ever be a production...
Hi
I know perfectly it is not possible to debug while the softdevice is enable and the Bluetooth is working. When I try to set up a breakpoint under these conditions, the...
hello there i want to communicate nrf51 and nrf52 using i2c protocol. [https://devzone.nordicsemi.com/question/75218/i2c-in-nrf51/?answer=75221#post-id-75221]
from this...
Hi ,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
The program detail of nrf51 as below:
-- sorftdevice : s130_nrf51_1.0...
Good morning,
I have designed a prototype based on nRF51822 device. Now, I want to program it with a demo software and I have the Ulink-me tool instead of Segger. From Keil...
Hey ,
I'm trying to implement a device that waits for the clicks from the user and sends it over ble as notifications.
i have written the header files for sensor . and from...
im trying to get my nrf51822 connecting only to my phone, I set the phone mac address on white list, but I cant connect to my phone (android) wiht nrf master control.
How...
When my program hits an error returned by an NRF API call, I get a hex number corresponding to that error from the app_error.c:
case NRF_FAULT_ID_SDK_ERROR:
m_error_data...
We've got devices that are out in the field which were built on SDK6.1 w/ 110 SoftDevice 7.1.0 on an nRF51822.
Went with the dual-banked solution as that was what was available...
We are developing a blood glucose meter based on the nRF51.
To comply with Bluetooth Continua, do we just implement the Glucose Profile and Service (GLP and GLS)?
Do you...
Hi everyone,
I pass few days to try to fix my issue whiteout success.
I'm working on UART example provide by SDK 10 and tried to set up a communication from my computer...
Because of the power-saving support, I want to disable the UART before Call the sd_app_evt_wait().
I referred to two following sites to know the procedure of the case....
I'm working with a nrf51422/s110 dev kit on which I downloaded the Heart rate Monitoring sample project. On my PC, using a s130 dongle, I connect the device and wrote some...
