I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I’m working with a device that communicates over single-wire UART (half-duplex), where TX and RX share the same line (because the peer device is designed that way). Now I...
Are there any unique design considerations to take into account when using the nRF54L series with RRAM? For example, are there any concerns about magnetic fields causing bit...
Hi all,
I'm trying to set up MCUMGR on 54L15, such that it can receive images from my border router when they're in the same Thread network. I read that we can upload images...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
I am getting a bt_hci_core: HCI driver open failed (-11) with a custom board using nrfConnect for VS Code and 2.9.1 toolchain/sdk.
The code is really simple (I'm not...
Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but it flash but can't run RF...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hello everyone,
I am currently working on implementing the flash protection feature for the 54L05 chip. My objective is to safeguard the code storage area from unintended...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hi,
I'm attempting to upgrade an existing project (which is still in the development stage) from NCS 2.7.0 to 3.0.2; this seems to break native TLS, and I'm not sure why...
I am working on project using thenRF9151 board and I require the GNSS functionality to work for the same. However, my board is not able to latch on to a satellite network...
We are certifying our device at KIWA. they are testing the WLAN adaptivity and the test is failing. Here is the failure description:
" It was a struggle to perform the...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
