Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hello,
I'd like to ask what needs to be configured to enable communication between two boards: nrF7002-DK and nRF5340-DK via another UART (e.g. UART1).
Please provide...
Hi
Are there any major OSes/stacks (e.g. Linux, Android, iOS) that provide support for the L2CAP feature so that we can test our Nordic device against?
Thanks
Hi,
I would like to know what is wrong with my code, which is presened below. Each time the timer is triggered I would like that the program writes four bytes into the...
I have a project that requires a bluetooth central to be used to gather data from a HRM service, which shouldn't be too much of an issue. However, it also has to store this...
I have searched here for an answer to this, but cannot find exactly what I am looking for. I am trying to put my Rev3 51822 to sleep and wakeup via GPIO. When I enable GPIO...
Whats the best way to secure my advertising packets such that others cannot make sense out of it?
Do we encrypt the packet data so that it is gibberish, random and not...
Hi!
We're running a S130 Stack to act as both Peripheral & Central at the same time. Everything is working fine but i i'm not quite sure about best approach for handling...
Hey ,
My application stores the data on BLE disconnect to pstorage succesfully.
But on reset if i try to read the data from pstorage it stops advertising, but the pstorage_load...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0.
I am able to doing dfu of softdevice and bootloader individually but when i try dfu for combined (SD + BL) then...
I can't find nrf.exe in C:\Program Files (x86)\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf
I only find nrfutil.exe in that folder.
Shall I use nrfutil.exe...
Softdevices have several separate version number systems:
a) the human-readable release version - used for hex file naming.
e.g. s110_nrf51_8.0.0, s120_nrf51_2.0.0
b...
Hi! I use a smart beacon kit (rev 1.0.0) and I would like to know how long the cpu is blocked during the data transmission/reception. I set the connection interval to 10ms...
We are designing a nRF52 based circuitry based on "53.2 Schematic QFAA QFN48 with DC/DC regulator setup"
In the reference diagram, there is an Optional block for the LFXO...
Hey all,
I've created HIDs using USB before which require a vendor ID (VID) and product ID (PID). Are these necessary when creating a device that uses HID over BTLE? If...
Is it possible for nRF52832 to drive an SPI TFT 240x240 LCD and a TWI Capacitive Touch Panel with BLE and NFC? Is 64Mhz the highest speed?
What I mean is that is it possible...
