This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Hi,
This time I am trying to work out the UART example.
I got it to the point where it is advertising, but the advertisement is wrong.
When I check with an Android...
Hi,
I have not yet experienced well on the design and development an application using nrf51 series. Your help will be very useful for my work. My question is as following...
Hi,
I have some problems with functions sd_ble_gap_disconnect and sd_ble_gap_adv_stop.
I got critical error when i try to disconnect or stop_adv and my phone is connected...
Hello,
In our application we don't allow bonding. Therefore I'm not allowing the application to send peer data to the bootloader using dfu_app_peer_data_set()...Therefore...
In NRF52-DK, I am currently working on NRF5 SDK 11.0.
In examples/peripheral/spi/pca10040/,
The master spi device is continuously sending "Nordic" string every 200msec...
I've submitted my product using nRF51822 chipset for Bluetooth certification. The BQE asks for QDID of proximity profile. Anyone knows about the QDID #?
Thanks,
Hello,
Is there a way to test packet corruption? My setup would be that I have my FW in nRF52-DK. Then I would test communication using nRF51-Dongle. I would like to force...
I want to connect two nRF51822-BKs and find their proximity. If one of the beacons go >5m away from the other beacon then one should beep/LED ON.
What is the best way to...
I have some troubles to understand the system clock functionality.
I am using a Module from Rigado which uses the nRF52 and has an external 32Mhz osc. on board.
In the...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
hi
i didn't manage to find detailed requirements on the voltage from the chip.
in the spec i see voltage range of :1.7-3.6v
but its not enough data for designing converter...
hi everyone, I am new to developing apps for nrf51822, and currently I want to learn first, I tried to google a lot around and could not look for the right resources, it would...
hi,
I would like to connect hid keypad with ipad,phone5s and android phone(all these have Bluetooth version 4 )but i couldn't connect this.ie, The nrf51822 module advertising...
I attempted to capture a waveform when running the SPI master example on nFR52 SDK/PCA10040. The source code I have as default and showing as follows
#define SPI0_ENABLED...
Hello,
We are working on a project that includes a countdown but we could not able to do it. Simply we want to do this:
Nrf51822 receives a signal-->run our funcion...
