Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I have a new nRF52-DK (PCA10040) and I'm trying to make some examples using arm-gcc. With freshly downloaded nRF5_SDK_11.0.0_89a8197 and Makefile.posix modified to point to...
What is the status of I2C pins and GPIO pins in the System OFF mode? Do they float once the SOC enters SYSTEM OFF mode? Here the accelerometer we are using consumes high current...
I tested Auto connect with NRF52832 UART APP(S132 softdevice), and nRF Master Control Panel APP.
I tested with samsung s3 neo and Moto G3 , but it is not working. In which...
I am currently using the watchdog in conjunction with RTX and a softdevice on the nrf51.
I am wondering if the default priority for the watchdog's interrupt works well in...
I am simulating button presses on a peripheral nRF51 device to determine average battery life. I send "button state" to central in a timer every 10s, with which I simulate...
Hi,
In my app , using SD130 , when i check the registers state while debuging i find that the RNB is powered on.
Do the SD130 power it on automatically? (because...
Hi All, We would like to use Alert Notification Service and UART service in our application. Here Our Peripheral will be Alert Notification client and UART Service server...
Hi, I have done the following:
Built a custom board with a brand new 128Kb nRF51822. On the board I only have the 16MHz xtal.
Routed out SWD IO/CLK and connected...
Apart from using nRF-Ready mother board, is there an option to program nRF2460. Probably through serial or third party SPI programmer? If yes, which one?
Is it possible to have one nRF2460 based transmitter to be received by multiple nRF2460 based receivers, or is the pairing one-to-one? In the datasheet, it says "The only...
Hi there,
I'm currently using the nRF UART app for iOS (v1.0.1), and I noticed it doesn't work the same as the Android app (v2). The key difference is the ability to select...
I am using external Crystal for my custom chip using nrf 51422 controller....
Just wanted to confirm is my setup for the external crystal (16 Mhz) is correct...
It is connected...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I'm using [nRF52_SDK_0.9.2] and original module. As a tool, I use the keil.
"NRF_POWER-> SYSTEMOFF = 1;" in the SDK example hrs also written, does not enter the system...
Respected SIR,
We procured nrf8002 BLE for our product. Currently we are in developing stage. We are using arm coertex M4-32bit based Teensy3.2 board as master. We havent...
