NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
Hello,
There's lots of questions and back and forth talking the nrf51 SDK both on here and on other sites, about the requirement for a product key to access and download...
Hi,
Using nRF51DK with softdevice 8.0 and sdk8.
I found the max number of whitelist in "ble_gap.h"...
/**@brief Maximum amount of addresses in a whitelist. */
#define...
Hi
I want to get the number of broadcast data.i try it as follow:
But i can not get the BLE_EVT_TX_COMPLETE event. Why? can you tell how to get the number of broadcast...
Searched -- without success -- the SDK docs extensively for access to the Transmit Window Size.
Wondering if there are ways we can manipulate it, and query the current...
Hi all,
I want to know how long it takes for NRF24LE1 to wake up from low power mode, especially in these situations:
1) Wakeup from pin voltage level , from Register...
Hi~
I am trying the example code of [--app-button-example-master--] from here... github.com/.../nrf51-app-button-example
for understanding button press features. I did...
Here i have made an UART0_IRQHandler routine. When i try to send some 50 bytes data through UART using PC tool here its receiving bytes, but it only receives 1st 6 bytes which...
Hi Everyone,
I'm working on adding DFU on my project and here is my setup:
Softdevice = 7.1.0
SDK = 6.1.0
DFU Bootloader = Keil compiled from SDK 6.1.0
MCP...
I'm having a bit of confusion understanding how the nRF51 Series Compatibility Matrix works.
I have a QFACA10 development board running my software perfectly, but when...
The nRF51822 Bluetooth Smart Beacon Kit User Guide (nRF51822-BK-UG) mentions an iOS project contained in the zip file nRFBeacons_iOS.zip. Where is this file? I cannot find...
Hello all,
I'm trying to save the service context with the Device Manager on the Central side. But I don't understand the implementation on how to do this. But no information...
I'm trying to adapt the BLE_BAS_C library to perform discovery and read/write operations for a custom service. However, when I change the UUID that I register with ble_db_discovery_evt_register...
i used this function to send data to my ble device ble_nus_string_send.this function sends ASCII values. and when i pass this function hex values it converts them into ascii...
Hello,
I was using wiringPiSPI() to connect via SPI and so i was using wiringPiISR function to create an interupt handler that will do callback to the user suplied function...
