Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
We have NRF51822 chips programmed for specific application and it is working fine as BLE services etc.
In some scenarios, to debug we want to stream data from our...
device_manager_peripheral.c provided via Software Packs in Keil doesn't compile against S110 8.0.0 (or 8.1.0). Its version shows up as 1.1.1. Same thing happens with bsp.h...
By combining some examples, I'm starting to understand how the UART examples works.
Using Keil 8.0.0, and the PCA10003 Board, I'm trying to send a burst of messages over...
I can see and bond nrf51 with android, but with iPhone nothing.
What can i implement for see nrf51 with iPhone?
Can i pair Iphone and nrf51?
Sorry for the very bad english...
The new generation of nRF51822's have a few neat new features, particularly the automatic power management piece, that I would like to potentially leverage in our project...
Hello,
I'm seeing some 67.2kHz reference spurs on the RF signal when I'm turning on the constant carrier mode using the DTM interface on the nRF51822. Layout and circuit...
Two applications using the same softdevice, s110, blinky and beacon from the examples.
Flashing softdevice and beacon successfully.
Replacing beacon app by blinky successfully...
The bootloader in SDK 8.1.0 (at /nRF51_SDK_8.1.0 examples/dfu/bootloader) calls pstorate_register() twice. The first time as part of bootloader_init(), then on bootloader_dfu_start...
hi,
I have implemented a UART to receive network packets from another controller to send it over BLE.
UART config are: 8bits data, 9600 baud rate, no parity, HW flow...
Hello,
I am wondering wether I need to pass regulatory tests when I use the S130 Softdevice together with a 3rd party module such as the one offered by raytac ( www.raytac...
Hi,
So i don't have any experience of working with nrf ble chips, but i was given nrf52 DK and i need to make it work as an iBeacon. So i got the dev board working without...
I'm planning to implement a mesh network, where each node (ble device) also acts as a scanner, detecting BLE advertise messages. The mesh network would then forward the advertisement...
I noted on the release notes for S110 v8 (DRGN-5556, NRFFOETT-986), that enabling/disabling blue_radio_notifications() while the Stack is not idle can cause an assert. Does...
