I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
I encounter a problem to switch to DFU mode from UART when BLE is connected and one 5ms timer keeps running for heart rate sensing alg. Maybe it's the reason keeps BLE busy...
Hi,
I want to use BLE to run DFU. My sdk is 8.1.1 and base project is ble_app_uart. When I use nrfgo Studio to program softdevice, bootloader and app, It can't enter app...
I am seeing excessive current in System ON, Idle mode. I am using WFI(). I have verified that
operation is being held at that instruction by using GPIO pin. Idle mode is...
Our manufacturer received new nRF51822QFAAH0 parts. Previously, we were supplied nRF51822QFG2 parts.
According to your PCN_092-1.2 Final.pdf document, there has been a...
Hi,
I can start MCP without the dongle PCA10031 (which I have updated the firmware on) and it starts ok, but when I then plug in and select the device COM 5 - 6xxxxxxxxx...
I would like to ask how to make advertisements which are less than one second. In my application, i need to scan for devices, when i find my specific device, i start to advertise...
I'm trying to programmate a simple blinkind led project to a custom board with a nRF51822 I did. I'm using a stm32 discovery to connect the custom board throw the SWD port...
I'm trying to update my beacon to use 8.0.0 SoftDevice 110. I've downloaded the 8.0.0 precompiled softdevice hex and loaded the Keil dfu_dual_bank_ble_s110_pca10028 project...
Hello,
I'm trying to use the APP_TIMER API to have tempo, but I've noticed a problem of accuracy when using the RTC1.
I use 0 as prescaler, so the RTC1 runs at 32768Hz...
Hello,
My question based on case, I've experienced recently.
nRF device that could advertise in general mode for limited time by pressing on button and continuously in...
Hello. I am having trouble setting up two PWM channels on nrf51822. The device is running S110 and SDK9.0.
The PWM initialization sequence looks almost identical to the...
Hi,
With reference to This link , I'm trying to make a Nordic solution which can support all beacon applications (iBeacon, Eddystone & Altbeacon).
I'm able to integrate...
Hello I am trying to program this nrf51822 module. I am using J link Cortex M9 . I want burn multilink peripheral in it.
I have followed this link.
I have connected everything...
