Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I am using nRF51822 controller for my development. I implemented the system sleep mode as below.
for (;;)
{
power_manage();
}
void power_manage(void)
{
uint32_t...
Hello, I found that there has been SDK update for NRF52 regarding NFC. Currently, it looks like NFC is just used for tagging.
I'd like to know whether I can use NFC peripheral...
Where can I find the BLE_GAP_EVT_ADV_REPORT value if I am using S310 SoftDevice?
Without it I cannot use my client to get advertising data from server. Or is there any other...
Hi Nordic:
I have two questions about SoftDevice s130:
Device A,B,C,D are using s130.
When this device (called A) is a peripheral and connected with a tablet...
Dear Nordic developers!
I am working on a project, which should use the ANT+ and the BLE communications, too. The S310 SoftDevice is good for them, but I have some problem...
Hi
I have been reading a lot of posts and the documentation on DFU for SDK7.2, but something is not really clear to me.
When I compile and program the boot loader in my...
Has anyone added an external power amplifier to the nRF24L01?. For my application, I need to increase rf power.
What about a skywork Amplifier ? if there is any amplifier...
Howdy all,
Has anyone added an external power amplifier to the nRF51822? From what I recall the BLE spec allows for 10mW output power (well, 10mW would be the maximum for...
Is there any recommended chip antenna for NRF52 SoC? Any guideline on the antenna placement, designing the matching circuit etc? I assume for NRF52, no need for an external...
I have moved bootloader from 8.0.0 SDK on top of our custom application. During boot, the softDevice transitions to bootloader as expected. The bootloader then advertises...
I'm using vanilla version of the dfu_dual_bank_ble_s110 project on top of my application. The problem is that the firmware enters bootloader mode whenever a USB is connected...
Is there a way to figure out for which target a binary in _build/ is compiled with Keil?
(other than parse .map or .lnp file for a file unique to the target)